IMER RB 130 Скачать руководство пользователя страница 8

8

IMER INTERNATIONAL S.p.A.

RB 130

PROBLEM

CAUSE

REMEDY

The motor does
not run when the
switch is pressed.

-Not power in the
supply line 

- The electric plug

and socket are not
connected properly.
- The cable from
the plug to the
electric panel is
broken.
- A wire has
become
disconnected inside
the panel.
- A wire has
become
disconnected on the
terminalboard.
- The switch is
faulty.
- The upstream

protection has

tripped.

- Check the line.

- Make a proper

connection.

- Replace the cable.

- Re-make the

connection.

- Re-make the

connection.

- Replace the

switch.

- Reset. If it will not

reset, have the
machine checked by
an electrician as

there may be a

safety fault.

or  disconnect  the  power  supply  (electric  motor  versions).

 

-  The  electric  motor  is  protected  from  thermal

overloads.  If  it  overheats  the  mixer  will  stop.  Allow  the
motor  to  cool  down  before  restarting.
5.  MAINTENANCE

 

WARNING..

Before  carrying  out  any  form  of  maintenance  work,
always  turn  the  mixer  off  (and  unplug  it  from  the  power
supply  in  electric  motor  versions).
- Replace worn or faulty components using original spare parts.
Any  repairs  to  the  electrical  system  must  be  carried  out  by
qualified personnel. Only IMER original spare parts must be used
and must not be modified in any way.
Due to its particular construction features, the ROLLBETA does
not  require  frequent  maintenance.  However,  it  is  advisable  to
change the oil in the reduction gear with ISO VG 460 oil at 40°C
after  2000  hours  of  work.
Check  that  the  contacts  of  the  plug-switch  unit  are  clean. Any
corrosion must be removed immediately.

 

-  Used  oil  is  classified  as  special  waste  by  law  and

must  be  treated  as  such.

 

-  Always  ensure  that  any  writing  or  signs  on  the

machine  are  legible.

5.1 CLEANING

After each daily work session or before long periods of inactivity,
the  mixer  drum  must  be  cleaned  thoroughly  both  inside  and
outside.

 

-  Before  cleaning  the  mixer,  always  switch  off  the

motor  and  disconnect  the  plug  from  the  motor  (even  when
using  brooms,  rags,  scrapers,  etc.).

 

-  Do  not  start  the  mixer  while  carrying  out  cleaning

operations.
When  using  a  hose  for  cleaning,  do  not  direct  the  jet  onto  the
plug-switch  unit.
Clean  the  outside  of  the  mixer  with  a  brush  and  water.  Scrape
off  any  cement  or  concrete  deposits.
There should not be any deposits  of cement or concrete inside
the drum.
To clean the inside of the drum at the end of work, put in a few
shovelfuls  of  gravel  and  water,  then  rotate  the  mixer.  This  will
prevent  any  residue  of  cement  or  concrete  in  the  drum  and  on
the mixing paddles from hardening.
The  mixing  drum  must  not  be  struck  with  hard  objects  such  as
hammers   shovels,  etc.  A  dented  drum  will  reduce  the  mixing
effectiveness  and  make  cleaning  more  difficult.
6.  NOISE  EMISSION  LEVEL
In chart 2 are indicated the level of sonorous power measured
L

WA

 following the EN ISO 3744 and the level of sonorous pressure

measured  by  the operator s  ear  L

pA

.

TABLE   2

CONCRETE

MIXER

TYPE OF MOTOR

L

pA

L

WA

ROLLBETA

EL 220V 50HZ

68 dB (A) 76 dB (A)

7.  TROUBLESHOOTING

Содержание RB 130




















Отзывы: