IEMCA Master 80 UP HyperFlexible страница 27 Скачать руководство пользователя | Manualshive

Страница: 27 / 190

background image

2 - TECHNICAL INFORMATION

Master 80 UP HyperFlexible

EN

2 - Pag. 11 / 11

The bar pusher (A) and remnant (C) are in their backwards limit stop position.
The clamps (D) close and the bar pusher moves backwards; the remnant is removed from the
collet. The clamps open, the bar pusher (A) moves forwards and place the remnant on the drop
guide (T), then bar pusher moves backwards, the clamps (D) close and open again for the
remnant drop check, and finally the remnant drop guide (T) is lowered and the remnant drops
on the remnant conveyor belt (E).

Remnant (C) is driven to the rear side and dropped in box (F). A sensor detects the remnant
during the path; if the remnant is still in the bar pusher collet the bar feeder stops, otherwise
the cycle goes on.

«
...
25
26
27
28
29
...
»

Содержание Master 80 UP HyperFlexible































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Master 80 UP HyperFlexible

Бренд: HALDER Страницы: 2

Бренд: Hakko Electronics Страницы: 16

Бренд: NARGESA Страницы: 37

Бренд: NARGESA Страницы: 6

Бренд: Nautilus Страницы: 17

Бренд: National Instruments Страницы: 6

Бренд: TATU Страницы: 30

Бренд: Rane Страницы: 4

Бренд: Sabio Страницы: 182

Бренд: UEi Страницы: 5

Бренд: UGO BASILE Страницы: 47

Бренд: UFO Страницы: 16

Бренд: ubicquia Страницы: 36

Бренд: Varimixer Страницы: 28

Бренд: PHAROS MARINE Страницы: 17

TRAKTOR KONTROL S3

Бренд: Native Instruments Страницы: 39

Бренд: K-SPORT Страницы: 4

Бренд: Baldan Страницы: 72

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды