IEMCA Master 80 UP HyperFlexible Скачать руководство пользователя страница 131

Страница: 131 / 190

7 - BAR FEEDER MAINTENANCE

Master 80 UP HyperFlexible

7 - Pag. 7 / 7

7.2.4 Air filter unit - Check

FILTER (A)

• Make sure that cup (B) is not full of condensate.

Drain the condensate by means of valve (C), if
necessary.

• The filter is equipped with a control pressure

switch, set to a pressure of 4.5 bar.

• To adjust the pressure switch proceed as

follows:

- remove the pressure gauge glass protection;

- turn the adjusting screw (D) counter

clockwise (+) to increase pressure or
clockwise (-) to decrease it;

- once finished, replace the pressure gauge

glass protection.

WARNING - CAUTION:

should the pressure switch pointer show a Pressure = 0, do not absolutely turn

the adjusting screw (D) clockwise (-), as it may cause the pressure switch

breakage.

Содержание Master 80 UP HyperFlexible































































































































































































Результаты поиска

Содержание Master 80 UP HyperFlexible

Отзывы:

Похожие инструкции для Master 80 UP HyperFlexible

Бренды по названию

Популярные бренды

IEMCA Master 80 UP HyperFlexible, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание Master 80 UP HyperFlexible

Отзывы:

Похожие инструкции для Master 80 UP HyperFlexible

Бренды по названию

Популярные бренды