IEMCA Master 80 UP HyperFlexible страница 139 Скачать руководство пользователя

Страница: 139 / 190

9 - PART REPLACEMENT

Master 80 UP HyperFlexible

9 - Pag. 3 / 3

9.3

REMNANT CONVEYOR BELT - REPLACEMENT

• Slacken the belt.
• Lift the belt.

WARNING - CAUTION:

During this manoeuvre be careful not to

damage the remnant passage door.

• Cut the worn belt so that it can be removed

from its seat.

• Splice one end of the worn belt with one end of

the new belt. Slide out the worn belt so that
the new one can be simultaneously inserted
along the entire path.

•  Separate the worn belt from the new one.
•  Splice the ends of the new belt using lacing A.
•  Tension the belt according to the instructions

given in § "Remnant conveyor belt", section 5

.
• Restore the bar feeder initial operating

conditions.

Содержание Master 80 UP HyperFlexible































































































































































































Результаты поиска

Содержание Master 80 UP HyperFlexible

Отзывы:

Похожие инструкции для Master 80 UP HyperFlexible

Бренды по названию

Популярные бренды

IEMCA Master 80 UP HyperFlexible, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание Master 80 UP HyperFlexible

Отзывы:

Похожие инструкции для Master 80 UP HyperFlexible

Бренды по названию

Популярные бренды