IEI Technology IMBA-8654 Скачать руководство пользователя

Страница: 39 / 242

IMBA-8654 Motherboard

Page 21

2.6.8 Intel

ICH5 USB Controller

Up to eight high-speed, full-speed or low-speed USB devices are supported by the ICH5.

High-speed USB 2.0, with data transfers of up to 480MB/s, is enabled with the ICH5

integrated Enhanced Host Controller Interface (EHCI) compliant host controller. USB

full-speed and low-speed signaling is supported by the four ICH5 integrated Universal

Host Controller Interface (UHCI) controller.

2.7 PCI Bus Components

2.7.1 PCI Bus Overview

The PCI bus controller on the ICH5 southbridge is compliant with PCI Revision 2.3

specifications and has a 33MHz PCI clock. The components listed below are all

connected to the PCI bus:

PCI slots on the motherboard

GbE interface

2.7.2 Realtek GbE interface

The Realtek 8110SC GbE controller is a 10/100/1000BASE-T Ethernet LAN controller.

The Realtek 8110SC combines a triple-speed IEEE 802.3 compliant Media Access

Controller (MAC) with a triple-speed Ethernet transceiver, a 32-bit PCI bus controller, and

embedded memory. Some of the Realtek 8110SC controller features are listed below:

Integrated 10/100/1000 transceiver

Auto-Negotiation with Next Page capability

Supports PCI rev.2.3, 32-bit, 33/66MHz

Supports CLKRUNB and MinPCI vl.0

Supports pair swap/polarity/skew correction

Crossover Detection & Auto-correction

Wake-on-LAN and remote wake-up support

Microsoft NDIS5 Checksum Offload (IP, TCP, UDP) and largesend offload

support

Supports Full Duplex flow control (IEEE 802.3x)

Содержание IMBA-8654



















































































































































































































































Результаты поиска

Содержание IMBA-8654

Отзывы:

Похожие инструкции для IMBA-8654

Бренды по названию

Популярные бренды

IEI Technology IMBA-8654, Руководство пользователя

Результаты поиска

Содержание IMBA-8654

Отзывы:

Похожие инструкции для IMBA-8654

Бренды по названию

Популярные бренды