IEI Technology IMBA-8654 Скачать руководство пользователя

Страница: 145 / 242

IMBA-8654 Motherboard

Page 127

6.3.4 Super IO Configuration

Use the IO Configuration menu (

BIOS Menu 7

) to set or change the configurations for the

FDD controllers, parallel ports and serial ports.

BIOS Menu 7: Super IO Configuration

OnBoard Floppy Controller [Enabled]

Use the

OnBoard Floppy Controller

to enable or disable the floppy controller. If a floppy

disk is not being used in the system, disabling this option frees up system resources that

can be redirected elsewhere in the system.

Disabled

Allows BIOS to disable the floppy controller

Enabled

EFAULT

Allows BIOS to enable the floppy controller

Serial Port1 Address [3F8/IRQ4]

Use the

Serial Port1 Address

option to select the Serial Port 1 base address.

Disabled

No base address is assigned to Serial Port 1

3F8/IRQ4 D

EFAULT

Serial Port 1 I/O port address is 3F8 and the interrupt

address is IRQ4

Содержание IMBA-8654



















































































































































































































































Результаты поиска

Содержание IMBA-8654

Отзывы:

Похожие инструкции для IMBA-8654

Бренды по названию

Популярные бренды

IEI Technology IMBA-8654, Руководство пользователя

Результаты поиска

Содержание IMBA-8654

Отзывы:

Похожие инструкции для IMBA-8654

Бренды по названию

Популярные бренды