IEI Technology IMBA-8654 Скачать руководство пользователя

Страница: 20 / 242

IMBA-8654 Motherboard

Page 2

1.1 IMBA-8654 Overview

The IMBA-8654 motherboard is an LGA775 Intel®

Pentium® 4/Intel®

Pentium® D/Intel®

Celeron® D CPU platform with an Intel® 865G Express Chipset and Intel® I/O Controller

Hub 5 (ICH5) Southbridge. The IMBA-8654 has a maximum front side bus (FSB)

frequency of 800MHz, supports up to 4GB of dual channel 333/400MHz DDR RAM and

comes with VGA, PS/2 keyboard/mouse, COM port, parallel port, serial port and audio

interfaces as well as a Realtek/Intel® (GbE). The IMBA-8654 supports up to two serial

ATA (SATA 3Gb/s) hard disk drives and up to eight USB 2.0 devices.

1.1.1 IMBA-8654 Features

Some of the IMBA-8654 features are listed below.

RoHS compliant

Support for the following CPUs:

LGA775 Intel

Pentium

LGA775 Intel

Pentium

LGA775 Intel

Celeron

Integrated Intel

Extreme 2 graphics engine

Maximum FSB of 800MHz

Four 184-pin dual channel 333/400MHz DDR SDRAM DIMMs support up to

4GB of memory

High performance Realtek or Intel® Gigabit Ethernet chipset

Two SATA 3Gb/s drives supported

Four Ultra ATA 100, Ultra ATA 66 or Ultra ATA 33 IDE HDDs supported

Eight USB 2.0 devices supported

ATX power only

Realtek ALC655 chipset with AC ’97 CODEC

Expansion:

1 x AGP 8X slot

6 x PCI expansion slots

1.2 IMBA-8654 Overview

Содержание IMBA-8654



















































































































































































































































Результаты поиска

Содержание IMBA-8654

Отзывы:

Похожие инструкции для IMBA-8654

Бренды по названию

Популярные бренды

IEI Technology IMBA-8654, Руководство пользователя

Результаты поиска

Содержание IMBA-8654

Отзывы:

Похожие инструкции для IMBA-8654

Бренды по названию

Популярные бренды