IEI Technology eKINO-945GSE Скачать руководство пользователя страница 99

Страница: 99 / 215

eKINO-945GSE Motherboard

Page 83

Step 5:

Connect LPT device

. Once the LPT interface connector is connected to the

chassis, the LPT device can be connected to the LPT interface connector. See

Figure 5-11

Step 5:

Figure 5-11: Connect the LPT Device

5.10 External Peripheral Interface Connection

The following external peripheral devices can be connected to the external peripheral

interface connectors.

RJ-45 Ethernet cable connectors

PS/2

devices

Serial port devices

USB

devices

VGA

monitors

To install these devices, connect the corresponding cable connector from the actual

device to the corresponding eKINO-945GSE external peripheral interface connector

making sure the pins are properly aligned.

Содержание eKINO-945GSE
























































































































































































































Результаты поиска

Содержание eKINO-945GSE

Отзывы:

IEI Technology eKINO-945GSE, Руководство пользователя, Страница: 99 / 215

Результаты поиска

Содержание eKINO-945GSE

Отзывы: