IEI Technology eKINO-945GSE Скачать руководство пользователя страница 133

Страница: 133 / 215

eKINO-945GSE Motherboard

Page 117

ANSI D

EFAULT

The target terminal type is ANSI

VT100

The target terminal type is VT100

VT-UTF8

The target terminal type is VT-UTF8

VT-UTF8 Combo Key Support [Disabled]

Use the

VT-UFT8 Combo Key Support

option to enable additional keys that are not

provided by VT100 for the PC 101 keyboard.

The VT100 Terminal Definition is the standard convention used to configure and conduct

emergency management tasks with UNIX-based servers. VT100 does not support all keys

on the standard PC 101-key layout, however. The VT-UTF8 convention makes available

additional keys that are not provided by VT100 for the PC 101 keyboard.

Disabled D

EFAULT

Disables the VT-UTF8 terminal keys

Enabled

Enables the VT-UTF8 combination key. Support for

ANSI/VT100 terminals

Sredir Memory Display Delay [Disabled]

Use the

Sredir Memory Display Delay

option to select the delay before memory

information is displayed. Configuration options are listed below

Delay

EFAULT

Delay 1 sec

Delay 2 sec

Delay 4 sec

Содержание eKINO-945GSE
























































































































































































































Результаты поиска

Содержание eKINO-945GSE

Отзывы:

IEI Technology eKINO-945GSE, Руководство пользователя, Страница: 133 / 215

Результаты поиска

Содержание eKINO-945GSE

Отзывы: