IEI Technology eKINO-945GSE Скачать руководство пользователя страница 113

Страница: 113 / 215

eKINO-945GSE Motherboard

Page 97

Enhanced D

EFAULT

Configures the on-board ATA/IDE controller to be in

Enhanced mode. In this mode, IDE channels and

SATA channels are separated. This mode supports

up to 6 storage devices. Some legacy OS do not

support this mode.

Legacy IDE Channels [PATA Pri, SATA Sec]

SATA Only

Only the SATA drives are enabled.

SATA Pri, PATA Sec

EFAULT

The IDE drives are enabled on the Primary

IDE channel. The SATA drives are enabled on

the Secondary IDE channel.

PATA Only

The IDE drives are enabled on the primary

and secondary IDE channels. SATA drives

are disabled.

IDE Master and IDE Slave

When entering setup, BIOS auto detects the presence of IDE devices. BIOS displays the

status of the auto detected IDE devices. The following IDE devices are detected and are

shown in the

IDE Configuration

menu:

Primary

IDE

Master

Primary

IDE

Slave

Secondary IDE Master

Secondary IDE Slave

The

IDE Configuration

menu (

BIOS Menu 4

) allows changes to the configurations for the

IDE devices installed in the system. If an IDE device is detected, and one of the above

listed four BIOS configuration options are selected, the IDE configuration options shown in

Section 87

6.3.2.1

appear.

Содержание eKINO-945GSE
























































































































































































































Результаты поиска

Содержание eKINO-945GSE

Отзывы:

IEI Technology eKINO-945GSE, Руководство пользователя, Страница: 113 / 215

Результаты поиска

Содержание eKINO-945GSE

Отзывы: