IEI Technology eKINO-945GSE Скачать руководство пользователя страница 118

Страница: 118 / 215

eKINO-945GSE Motherboard

Page 102

UDMA3

Ultra DMA mode 3 selected with a maximum data transfer

rate of 44 MB/s (To use this mode, it is required that an

80-conductor ATA cable is used.)

UDMA4

Ultra DMA mode 4 selected with a maximum data transfer

rate of 66.6 MB/s (To use this mode, it is required that an

80-conductor ATA cable is used.)

UDMA5

Ultra DMA mode 5 selected with a maximum data transfer

rate of 99.9 MB/s (To use this mode, it is required that an

80-conductor ATA cable is used.)

S.M.A.R.T [Auto]

Use the

S.M.A.R.T

option to auto-detect, disable or enable Self-Monitoring Analysis and

Reporting Technology (SMART) on the drive on the specified channel.

S.M.A.R.T

predicts

impending drive failures. The

S.M.A.R.T

BIOS option enables or disables this function.

Auto D

EFAULT

BIOS auto detects HDD SMART support.

Disabled

Prevents BIOS from using the HDD SMART feature.

Enabled

Allows BIOS to use the HDD SMART feature

32Bit Data Transfer [Enabled]

Use the

32Bit Data Transfer

BIOS option to enables or disable 32-bit data transfers.

Disabled

Prevents the BIOS from using 32-bit data transfers.

Enabled D

EFAULT

Allows BIOS to use 32-bit data transfers on supported

hard disk drives.

Содержание eKINO-945GSE
























































































































































































































Результаты поиска

Содержание eKINO-945GSE

Отзывы:

IEI Technology eKINO-945GSE, Руководство пользователя, Страница: 118 / 215

Результаты поиска

Содержание eKINO-945GSE

Отзывы: