IEI Technology eKINO-945GSE Скачать руководство пользователя страница 32

Страница: 32 / 215

eKINO-945GSE Motherboard

Page 16

Supports the four USB 2.0 devices on the eKINO-945GSE with four UHCI

controllers and one EHCI controller

Complies with System Management Bus (SMBus) Specification, Version 2.0

Supports Audio Codec ’97 (AC’97) Revision 2.3

Supports Intel® High Definition Audio

Contains Low Pin Count (LPC) interface

Supports Firmware Hub (FWH) interface

Serial peripheral interface support

2.5.1 Audio Codec ’97 Controller

The Audio Codec ’97 (AC’97) controller integrated into the Intel® ICH7M complies with

AC’97 Component Specification, Version 2.3. The AC’97 controller is connected to the

following audio jacks on the external connector panel.

Stereo

output

Microphone

input

2.5.2 IDE Interface

The IDE interface connects with

2.5.2.1 IDE Connector ........................................................................... 16

2.5.2.2 CompactFlash® Slot .................................................................. 17

2.5.2.1 IDE Connector

The IDE connector on the Intel® ICH7M Southbridge connects to an IDE hard disk or

other IDE device. The IDE connector is shown in

Figure 2-5

PIO IDE transfers up to 16 MB/s and Ultra ATA transfers of 100 MB/s. The integrated IDE

interface is able to support the following IDE HDDs:

Ultra ATA/100

, with data transfer rates up to 100 MB/s

Ultra ATA/66

, with data transfer rates up to 66 MB/s

Ultra ATA/33

, with data transfer rates up to 33 MB/s

Содержание eKINO-945GSE
























































































































































































































Результаты поиска

Содержание eKINO-945GSE

Отзывы:

IEI Technology eKINO-945GSE, Руководство пользователя, Страница: 32 / 215

Результаты поиска

Содержание eKINO-945GSE

Отзывы: