IEI Technology eKINO-945GSE Скачать руководство пользователя страница 74

Страница: 74 / 215

eKINO-945GSE Motherboard

Page 58

The RJ-45 Ethernet connector has two status LEDs, one green and one yellow. The green

LED indicates activity on the port and the yellow LED indicates the port is linked. See

Table 4-22

Status

Description

Status

Description

Green Activity

Yellow Linked

Table 4-22: RJ-45 Ethernet Connector LEDs

4.3.4 Serial Port Connectors

CN Label:

COM1 (top) and COM2 (bottom)

CN Type:

DB-9 connectors

CN Location:

See

Figure 4-24

CN Pinouts:

See

Table 4-23

and

Figure 4-27

The serial port connectors connect to RS-232 communications devices.

Pin No.

Description

Pin No.

Description

1 DCD

6 DSR

2 RX

7 RTS

3 TX

8 CTS

4 DTR

9 RI

5 GND

Table 4-23: RS-232 Serial Port Pinouts

Figure 4-27: RS-232 Serial Port Pinout Locations

Содержание eKINO-945GSE
























































































































































































































Результаты поиска

Содержание eKINO-945GSE

Отзывы:

IEI Technology eKINO-945GSE, Руководство пользователя, Страница: 74 / 215

Результаты поиска

Содержание eKINO-945GSE

Отзывы: