IEI Technology eKINO-945GSE Скачать руководство пользователя страница 177

Страница: 177 / 215

eKINO-945GSE Motherboard

Page 161

8.2.2.2 Battery Detection

When the smart battery is connected to the AUPS series power module, the AUPS Battery

Status Monitor detects it and shows in the screen as

Figure 8-9

. Two batteries can be

connected to the AUPS series power module at the same time. The second battery

information is shown in the

Battery A Detection

section if connected.

Figure 8-9: Battery Detection

The battery is connected to the AUPS series.

Off

The battery is not connected to the AUPS series.

Full

The battery is fully charged.

Low

The battery is low.

Using

The battery is being used.

Charging

The battery is being charged.

Standby

The battery is fully charged and ready to be used anytime.

>60 C

The battery temperature is above 60°C.

<60 C

The battery temperature is below 60°C.

Table 8-1: Status Settings

Содержание eKINO-945GSE
























































































































































































































Результаты поиска

Содержание eKINO-945GSE

Отзывы:

IEI Technology eKINO-945GSE, Руководство пользователя, Страница: 177 / 215

Результаты поиска

Содержание eKINO-945GSE

Отзывы: