manualshive.com logo in svg

IDT PCI Express 89HPES32NT24xG2, Руководство пользователя, Страница: 78 / 744

Поделиться
Скачать
IDT PCI Express 89HPES32NT24xG2 Скачать руководство пользователя страница 78

IDT   Reset and Initialization

PES32NT24xG2 User Manual

3 - 14

January 30, 2013

Notes

state. Although not a hot reset, this has the same functional effect on downstream components.

2.  All registers fields in all registers associated with downstream switch ports, except those designated

Sticky and SWSticky, are reset to their initial value. The value of fields designated Sticky or
SWSticky is unaffected by an Upstream Secondary Bus Reset.

3.  All TLPs received from downstream switch ports and queued in the switch are discarded.

4.  Logic in the stack and switch core associated with the downstream switch ports are gracefully reset.

5.  Wait for software to clear the SRESET bit in the BCTL register of the upstream switch port’s PCI-to-

PCI bridge function.

6.  Normal downstream switch port operation begins. 

The operation of the upstream switch port is unaffected by a secondary bus reset. The link remains up

and Type 0 configuration read and write transactions that target the upstream port function(s) complete
normally. 

–

The DMA and NT functions (if present in the upstream port of the partition) are unaffected and
continue to operate normally.

During an Upstream Secondary Bus Reset, all TLPs destined to the secondary side of the upstream

switch port’s PCI-to-PCI bridge are treated as unsupported requests.

Partition Downstream Secondary Bus Reset

A partition downstream secondary bus reset may be initiated by the following condition:

–

A one is written to the Secondary Bus Reset (SRESET) bit in the Bridge Control (BCTL) register
of the PCI-to-PCI bridge function in a downstream switch port.

When a downstream secondary bus reset occurs, the following sequence of actions take place on logic

associated with the affected partition.

–

If the corresponding downstream switch port’s link is up, TS1 ordered sets with the hot reset bit
set are transmitted.

• If the link associated with a downstream switch port is in the Disabled LTSSM state, then a hot

reset will not be propagated out on that port. The port will instead transition to the Detect LTSSM
state. Although not a hot reset, this has the same functional effect on downstream components.

–

All TLPs received from corresponding downstream switch port and queued are discarded.

–

Wait for software to clear the Secondary Bus Reset (SRESET) bit in the downstream switch port’s
Bridge Control Register (BCTL).

–

Normal downstream switch port operation begins. 

The operation of the upstream switch port is unaffected by a partition downstream secondary bus reset. 

The operation of other downstream switch ports in this and other partitions is unaffected by a partition

downstream secondary bus reset. During a partition downstream secondary bus reset, type 0 configuration
read and write transactions that target the downstream switch port complete normally. During a partition
downstream secondary bus reset, all TLPs destined to the secondary side of the downstream switch port’s
PCI-to-PCI bridge are treated as unsupported requests.

Port Mode Change Reset

A port mode change reset occurs when a port operating mode change is initiated and the OMA field in

the corresponding SWPORTxCTL register specifies a reset. Port mode change reset behavior is described
in section Reset Mode Change Behavior on page 5-21.

Содержание PCI Express 89HPES32NT24xG2









































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов