IDEAL Evomax 30 Скачать руководство пользователя

Страница: 47 / 62

EVOMAX

Installation & Servicing

SERVICInG

SER

VICI

64 GAS VALVE REPLACEmEnt

Refer to Frame 55.

Remove the upper front panel (Refer to frame 57).

Remove the fan and gas assembly (Refer to frame 58).

Remove the 3 screws holding the gas valve to the venturi

(30,40,60,80 only).

Remove the venturi from the fan to access the gas valve

fixing screws (100/120 only Refer to frame 63).

Remvove the four screws retaining the gas valve.

Remove the venturi from the mixture chamber before

removing the gas valve (as in (4) - 150 only).

Remove the 4 screws retaining the inlet flange to gas valve &

transfer to new valve (100/120 only).

Fit new gas valve to venturi using the new seal provided,

ensure gas injector is fitted correctly.

10.

Reassemble in reverse order replacing all gaskets.

11.

Check the operation of the boiler (Refer to frame 55).

Evomax 30, 40 & 60

Evomax 80

Evomax 100

Evomax 120

206210-10389_3

Evomax 150

176272

176273

176274

176359

176360

176361

176362

175232

174381

176362

176313

176358

176313

176368

176558

176369

176559

176370

176560

176371

176561

176373

176371

Model

30P

40P

60P

80P

100

120

150

Fan

Venturi

Gas Management Assembly Part No’s

Valve

Injector

206210-3.indd 47

09/06/2011 13:34:55

Содержание Evomax 30































































Результаты поиска

Содержание Evomax 30

Отзывы:

Похожие инструкции для Evomax 30

Бренды по названию

Популярные бренды

IDEAL Evomax 30, Руководство по установке и обслуживанию

Результаты поиска

Содержание Evomax 30

Отзывы:

Похожие инструкции для Evomax 30

Бренды по названию

Популярные бренды