IDEAL Evomax 30 Скачать руководство пользователя страница 4

Страница: 4 / 62

EVOMAX

Installation & Servicing

GEnERAL

IntRoDuCtIon

The EVOMAX boilers are fully automatically controlled, wall

mounted, fanned, super efficient condensing appliances.
The EVOMAX condensing boilers can be installed either on the

wall or into a prefabricated floor mounted frame.
The boilers are suitable for use with a room sealed flue or open

flue application.
Through a sophisticated control system combined with premix

burner arrangement the boilers are capable of high seasonal

efficiencies of >96% and low emissions.
These boilers are certified to meet the requirements of the EC

Gas Appliance Directive, Boiler Efficiency Directive, EMC and Low

Voltage Directive.

note.

These boilers cannot be used on systems that include

gravity circulation.

The boiler are suitable for connection to fully pumped, open vented

or sealed water systems. Adequate arrangements for completely

draining the system by provision of drain cocks MUST be provided

in the installation pipework.

oPtIonAL EXtRA kItS

• Vertical Roof Flue Kit 80/125

• Vertical Roof Flue Kit 100/150

•

Horizontal Wall Flue Kit 80/125

• Horizontal Wall Flue Kit 100/150

•

open flue kit 80

•

open flue kit 100

•

Pitched and flat Roof tiles

•

frame and Header kits

• Pump Kits

•

Programmable Room thermostat kit

•

modulating Sequencer kit

•

outside Sensor kit

•

tank Sensor kit

• Room Sensor Kit

• Safety Interlock Kit

SAfEty

Current Gas Safety (Installation and use) Regulations

or rules in force

The appliance is suitable only for installation in GB and IE and

should be installed in accordance with the rules in force.
In GB, the installation must be carried out by a Gas Safe

Registered Engineer or in IE by a competent person. It must be

carried out in accordance with the relevant requirements of the:

•

Gas Safety (Installation and Use) Regulations

•

The appropriate Building Regulations either The Building

Regulations, The Building Regulations (Scotland), Building

Regulations (Northern Ireland).

•

The Water Fittings Regulations or Water byelaws in Scotland.

•

The Current I.E.E. Wiring Regulations.

Where no specific instructions are given, reference should be

made to the relevant British Standard Code of Practice.

In IE, the installation must be carried out by a Competent Person

and installed in accordance with the current edition of I.S.813

“Domestic Gas Installations” or I.S. 820 “Non-Domestic Gas

Installations” as appropriate, the current Building Regulations and

reference should be made to the current ETCI rules for electrical

installation.

The Evomax boilers have been tested and certified to;
EN 483, EN 677, PREN 15420, BSEN 15417, BSEN 656, BSEN

60335-2-102, BSEN 55014-1 and BSEN 55014-2 for use with

Natural Gas & LPG.
Detailed recommendations are contained in the following Codes of

Practice:
BS. 6891

Installation of low pressure gas pipework of up to

28mm (R1) in domestic premises (2nd family gas).

BS. 5482 Pt. 1 Domestic butane and propane gas burning

installations.

BS. 5440

Inst. and maintenance of flues and ventilation for gas

appliances of rated input not exceeding 70kW net

(1st, 2nd and 3rd family gases).

Part 1

Specification for installation of flues.

Part 2

Specification for installation and maintenance of

ventilation for gas appliances.

BS. 6644 : 2005 Installation of gas fired hot water boilers of rated

inputs between 70kW and 1.8MW (net) (2nd and

3rd family gases).

BS. 6798

Installation and maintenance of gas fired hot water

boilers of rated input not exceeding 70kW net.

BS. 6880

Low temperature hot water heating systems of

output greater than 45kW.

Part 1 Fundamental and design considerations.

Part 2 Selection of equipment.

Part 3 Installation, commissioning and maintenance.

BSEN.12828:2003 Heating Systems in buildings: Design for water

based systems.

BSEN.12831:2003 Heating Systems in buildings: Method for

calculation of the design heat load.

BSEN.13831

Specification for: Expansion vessels using an

internal diaphragm, for sealed hot water heating

systems.

BSEN.14336:2004 Heating Systems in buildings: Installation and

commissioning of water based heating systems.

IGE/UP/1

Soundness testing and purging of industrial and

commercial gas installation.

IGE/UP/2

Gas installation pipework, boosters and

compressors on industrial and commercial

premises.

IGE/UP/10

Installation of gas appliances in industrial and

commercial premises.

Where reference is made throughout these instructions I.S.813:2002

“Domestic Gas Installations” reference should also be made to

I.S.820:2000 “Non-Domestic Gas Installations” as applicable.

SAfE HAnDLInG

This boiler may require 2 or more operatives to move it to its installation

site, remove it from its packaging base and during movement into its

installation location. Manoeuvring the boiler may include the use of a

sack truck and involve lifting, pushing and pulling.
Caution should be exercised during these operations.
Operatives should be knowledgeable in handling techniques when

performing these tasks and the following precautions should be

considered:
•  Grip the boiler at the base.
•   Be physically capable.
•   Use personal protective equipment as appropriate, e.g. gloves,

safety footwear.

notE to tHE InStALLER: LEAVE tHESE InStRuCtIonS ADJACEnt to tHE GAS mEtER.

206210-3.indd 4

09/06/2011 13:34:04

Содержание Evomax 30































































Результаты поиска

Содержание Evomax 30

Отзывы:

Похожие инструкции для Evomax 30

Бренды по названию

Популярные бренды

IDEAL Evomax 30, Руководство по установке и обслуживанию

Результаты поиска

Содержание Evomax 30

Отзывы:

Похожие инструкции для Evomax 30

Бренды по названию

Популярные бренды