IDEAL Evomax 30 Скачать руководство пользователя

Страница: 11 / 62

EVOMAX

Installation & Servicing

InStALLAtIon

8 PREPARInG tHE WALL

7 WALL mountInG tEmPLAtE

note

The template shows the positions for the

top fixing holes. Care must be taken to ensure

the correct holes are drilled.

Tape template into the selected position.

Ensure squareness by hanging a plumbline.

Mark on to the wall:

a. The top 4 wall mounting plate screw

positions.

b. The 2 boiler lower fixing positions using

diagram below

c. The position of the flue duct. Mark

the centre of the hole as well as the

circumference.

Remove the template from the wall.

ImPoRtAnt

. Ensure that, during the cutting

operation, masonry falling outside of the building

does not cause damage or personal injury.

Cut the flue hole ensuring that the hole

is square to the wall. Both wall faces

immediately around the cut hole should be flat.

Drill 4 boiler top fixing holes with a 12mm

(

”) masonry drill and insert the plastic plugs

provided, for the wall mounting plate.

Drill the 2 boiler lower fixing holes with a 12mm

(

”) masonry drill, insert the plastic plugs

provided .

Fix the wall bracket into place with 4 M10x70

hex head coach screws provided.

ima5400

104

Vertical Offset From X mm

Distance from flue centre line (Y) to outside wall surface.
For lengths greater than 4m, increase offset (X) by 26mm

for every additional 1m.

note

: Horizontal flue runs must be

inclined at 1.5-3

to the horizontal to allow

condensate to drain back to the boiler.

ALLA

Ion

850mm to top of boiler

18mm

332mm

Ø12mm

BOILER LOWER FIXING POSITIONS

206210-3.indd 11

09/06/2011 13:34:16

Содержание Evomax 30































































Результаты поиска

Содержание Evomax 30

Отзывы:

Похожие инструкции для Evomax 30

Бренды по названию

Популярные бренды

IDEAL Evomax 30, Руководство по установке и обслуживанию

Результаты поиска

Содержание Evomax 30

Отзывы:

Похожие инструкции для Evomax 30

Бренды по названию

Популярные бренды