IDEAL Evomax 30 Скачать руководство пользователя

Страница: 33 / 62

EVOMAX

Installation & Servicing

InStALLAtIon

ALLA

Ion

41 EVomAX uSER IntERfACE - ADVAnCED oPERAtInG InStRuCtIonS ContInuED....

ENAblING VAlVE POWER OPEN/VAlVE POWER ClOSEd/SHUNT PUMP

The boiler default setting is the CH Pump output will only be On for a CH

Demand and the DHW Pump output will only be on for a DHW Demand.

This can be changed so that the CH Pump output controls the system pump

and the DHW Pump output operates a Valve (power open or power shut)

This can also be changed so that the CH Pump output controls a system

pump and the DHW Pump output controls a shunt pump
Press SELECT and then hold + and - down together for more than 5s, the

following screen will be displayed

Installer Mode

normal operation

Set Flow Temp’
Set DHW Temp’

Rotate the KNOB clockwise until the following screen is displayed

Installer Mode
Set Night Setback

dHW Pump/Valve

Set Booster
CH/DHW Priority

Press SELECT and the following screen will be displayed

DHW Pump/Valve

Pump

Valve Power Open
Press - for more

Press + and - to change to the required setting and then press ENTER

to store
Rotate the KNOB anti-clockwise until Normal Operation is highlighted

again and press SELECT to return to normal operation

continued . . . . . . . .

EnAbLInG nIGHt SEtbACk

Note- Night Setback is only operational if Outside Sensor has been connected

When Night Setback is enabled the boiler will run at the normal flow temp.

during CH Demand and reduced temperature when for no demand
Press SELECT and then hold + and - down together for more than 5s, the

following screen will be displayed

Installer Mode

normal operation

Set Flow Temp’
Set DHW Temp’

Rotate the KNOB clockwise until the following screen is displayed

Installer Mode
Set to 0-10V Input

Set night Setback

DHW Pump / Valve
Set Booster

Press SELECT and the following screen will be displayed

Set Night Setback
On

off

Press + and - to change to required setting and then press ENTER to store

Rotate the KNOB anti-clockwise until Normal Operation is highlighted

again and press SELECT to return to normal operation

Installer Mode

normal operation

Set Flow Temp’
Set DHW Temp’

Note- Booster Function is only operational if Outside Sensor has

been connected

If Booster function is enabled and CH Demand is ongoing for more

than 10 minutes then the Flow Temp. target is increased by 10°C

When the Burner switches off the temperature is reset
Press SELECT and then hold + and - down together for more than

5s, the following screen will be displayed

Rotate the KNOB clockwise until the following screen is displayed

Installer Mode
DHW Pump / Valve

Set booster

CH/DHW Priority
Set Max Flow Temp’

Press SELECT and the following screen will be displayed

Set Booster
On

off

Press + and - to change to required setting then press ENTER to store

Rotate the KNOB anti-clockwise until Normal Operation is highlighted

again and press SELECT to return to normal operation

CHANGING CH / dHW PRIORITy

Installer Mode

normal operation

Set Flow Temp’
Set DHW Temp’

The boiler default setting is DHW always has priority ahead of CH

It is possible to change this so CH always has priority ahead of DHW

or the boiler alternates between DHW and CH every 10 mins

Press SELECT and then hold + and - down together for more than 5s,

the following screen will be displayed

Rotate the KNOB clockwise until the following screen is displayed

Installer Mode
Set Booster

CH/dHW Priority

Set Max Flow Temp’
Set Min Flow Temp’

Press SELECT and the following screen will be displayed

CH/DHW Priority

Priority = DHW

Priority = CH
Priority = Equal

Press + and - to change to the required setting and then press

ENTER to store
Rotate the KNOB clockwise until Normal Operation is highlighted

again and press SELECT to return to normal operation

206210-3.indd 33

09/06/2011 13:34:32

Содержание Evomax 30































































Результаты поиска

Содержание Evomax 30

Отзывы:

Похожие инструкции для Evomax 30

Бренды по названию

Популярные бренды

IDEAL Evomax 30, Руководство по установке и обслуживанию

Результаты поиска

Содержание Evomax 30

Отзывы:

Похожие инструкции для Evomax 30

Бренды по названию

Популярные бренды