background image

7

Viceroy GTS - 

Installation & Servicing

GENERAL

Air inlet

B

Air outlet

550 mm

1.5 m

1 m

*

1 m

*

A

C

vic9106

Refer to notes above

Refer to notes above

2  BOILER CLEARANCES

The minimum dimensions as indicated must be respected to 

ensure good access around the boiler.

Note. 

To allow the inlet of the combustion air, the boiler room 

must be adequately ventilated, the section and the location of 

which must comply with local recommendations.

Refer also to Frame 3.
The boiler must be positioned so that there is enough space 

available to allow the following:

• 

Access around the boiler for servicing.

• 

Space to open the boiler front door.

• 

Space to access the burner.

Recommended minimum clearances are as follows:

Rear

  1000mm or adequate space to make the flue connections 

and access to the flue sample point, drain connection, flue 

and smokehood cleanout doors and any safety or control 

devices.

Sides

  One side may be 100mm the other side must be 200mm 

plus the burner projection or 500mm whichever is the 

greater to allow the burner door to be swung open and 

maintain access to the rear.    In multiple boiler installations 

both sides may be 100mm except at one end consideration 

must also be given to the burner door hinge position and 

consequent clearance for access to the rear.

Front

  See Table below.

567

R = 41

5

R = 751,

5

15

240

burner door open

View from top

R = 751.5

vic7084

  GTS 8 

GTS 9 

GTS 10 

GTS 11 

GTS 12 

GTS 13 

GTS 14

 

1505  1665  1825  1985  2145  2305 2465

 105 

105 

105 

105 

105 

105 

105

 1500 

2000 

2000 

2000 

2500 

2500 

2500

A
B
C

Dimension

Boiler

mm
mm
mm

Содержание VICEROY GTS 8





































Отзывы: