background image

32

Viceroy GTS - 

Installation & Servicing 

SERVICING

VIC711

5

Vacuum
cleaner

51  MAINTENANCE

WARNING

The operations described below shall always be performed 

with the boiler and the power supply switch off.

The boiler front panel has to be removed to access the various 

devices to be maintained and checked.

1.  Unhook the front panels and remove.

Cleaning the Casing Material

Use a soapy solution and sponge only.  Rinse with clean water 

and dry with chamois leather or soft cloth.

52  CLEANING THE FLUEWAYS

1. 

Close off the fuel supply to the burner.

2. 

Ensure that the boiler has been cooled 

to ambient temperature.

3.

  Isolate the mains supply to the boiler 

and burner.

4.

  Disconnect the cable and supply pipe to 

the burner.

5.

  Open the combustion chamber (four 

nuts) and flue way (three nuts) doors by 

removing the nuts.

6.

  Remove the flue way baffles.

7.

  Thoroughly clean the flue ways and 

baffles.

8.

  Release and allow to swing down the 

rear cleanout covers by undoing the two 

upper nuts and loosening the two lower 

nuts.  Dispose of the debris/soot that 

may have accumulated.

9. 

Replace the rear cleanout covers 

after first inspecting and if necessary 

replacing the seal.

10. 

Brush out the combustion chamber and 

vacuum the soot from beneath the flue 

ways.

11.

 Replace the flue baffles into the flue 

ways (refer to Frame 25 for number and 

location).

12.

 Check the condition of the combustion 

chamber door insulation and replace if 

necessary.

13.

 Check the condition of the combustion 

chamber door seal and replace if 

necessary.

14. 

Refer to the burner manufacturer's 

Instructions for burner maintenance.

vic9123

Brush and

vacuum cleaner

Brush

 

vic9126

Vacuum
cleaner

vic7116

SER

VICING

Содержание VICEROY GTS 8





































Отзывы: