manualshive.com logo in svg

IdeaFly MARS, Руководство оператора, Страница: 6 / 40

Поделиться
Скачать
IdeaFly MARS Скачать руководство пользователя страница 6

6

MARS

QUADCOPTER OPERATOR’S MANUAL

The following items are required to fly your new Mars series quadcopter. Items required can be purchased through 

your local Hobby People retail store or online from 

www.hobbypeople.net.

iTEMS REQUiRED

These warnings and safety notes are important and must be followed closely. Please abide by this information and 

follow the instructions in this Operator’s Manual to ensure maximum safety. It’s important that you fully understand 

not only how to operate your quadcopter, but also to fully understand the responsibility you have for its proper use - both 

for your safety and the safety of others.

wARNiNGS AND SAfETy NOTES

SAfE AND LEGAL USE Of yOUR QUADCOPTER

Your quadcopter is not intended for commercial use. It must be used 

in a safe and legal manner only. By operating your quadcopter, the 

user accepts full responsibility for its safe and legal use. Follow all 

privacy laws and property laws when operating your quadcopter, and especially when using a still or video camera. 

The camera gimbal included with the quadcopter is to be used for hobbyists and/or amateur video or photography 

only. For Safe Operation Guidelines, please visit the Know Before You Fly website at 

www.knowbeforeyoufly.org.

PROPELLER SAfETy

Your Mars series quadcopter’s propellers are thin and very sharp. Although they are somewhat flexible to prevent 

damage during minor mishaps, they can still be very dangerous.

• Hobby People 3S 6400mAh LiPo Battery w/Female XT60 Power Connector 

(P/N 118412)

 or similar 3S 3000 to 

6400mAh 20C or Greater LiPo Battery. See Maximum Battery Dimensions Above.

• Hobby People Ultra 100 Multi-Chemistry Balance Charger 

(P/N 118561)

• Idea-Fly WiFi Sports Cam 1080P 

(P/N 116380)

 - Optional for Standard Version, Required for FPV Version

• Hobby People Micro USB FPV Video Cable 

(P/N 163452)

 - Included with 116380, Required for Others (FPV Version Only) 

 

• Hobby People XT60 Battery Adapter for Charger - 4mm Bullet to XT60 Female 

(P/N 118542)

• Ultra-Last 8 ‘AA’ Alkaline Batteries for Transmitter 

(P/N 849440)

• Hobby People LiPo Battery Low Voltage Alarm* 

(P/N 118531)

• Hobby People Mini USB Cable 

(P/N 163452)

 for Programming and Firmware Updates**

(P/N 849839)

(P/N 118561)

(P/N 163452)

(P/N 118542)

* When your LiPo battery voltage drops to the low voltage cutoff value during flight, the LED Condition Indicator will 

flash red rapidly to indicate you must land immediately. For extra precaution, we suggest using a programmable 

LiPo Battery Voltage Alarm that can be mounted with your LiPo battery inside the quadcopter. You are able to 

program the alarm to sound at a higher cutoff voltage value to give you more time to safely land before the 

battery voltage drops too low and results in a crash.

**Not required for basic flying, but programming is required for best performance.

The propellers must be removed from the motors whenever you calibrate the transmitter control sticks or when 

you update the flight controller firmware, or whenever there’s any question about safely operating the quadcopter.

• Do not attempt to fly the quadcopter if one or more of the propellers are damaged. Flying with damaged propellers 

is not safe and can make the quadcopter fly uncontrollably. Check the propellers prior to each flight. If a propeller 

appears damaged in any way, it should be replaced. 

Be very careful not to cut yourself if and when you 

unscrew the propellers to replace them.

(P/N 118531)

BE CAREFUL! DO NOT ALLOw YOUR FINGERS, HANDS OR OTHER BODY PARTS TO COME INTO

CONTACT wITH THE SPINNING PROPELLER BLADES OR SERIOUS INjURY wILL RESULT!

(P/N 116380)

Battery dimensions should not exceed 5-1/4 (L) x 1-5/8 (W) x 1-1/2 (H) (133 x 41 x 38mm)

(P/N 118412)

(P/N 163452)

Содержание MARS









































Отзывы:

Нет отзывов