IdeaFly MARS Скачать руководство пользователя

Страница: 3 / 40

MARS

QUADCOPTER OPERATOR’S MANUAL

Idea-Fly/Hobby People guarantees this product to be free from manufacturer defects in both material and

workmanship at the time of purchase. Idea-Fly/Hobby People will repair or replace at our discretion, equipment

determined to be defective, otherwise, the user is responsible for any charges for the repair or replacement of the

equipment in question. This warranty does not cover cosmetic damage, nor does it cover damage caused by

misuse, modification, negligence, abuse, improper connections, acts of God or damage caused by alterations by

unauthorized persons. This warranty only applies to the original purchaser and requires proof of purchase to redeem.
Idea-Fly/Hobby People shall not be liable for any damage resulting from the use of this product. As Idea-Fly/Hobby

People has no control over the use, setup, modification or misuse of this product, no liability shall be assumed nor

accepted for any resulting damage or injury. By the act of using this product, the user accepts all resulting liability.

In no case shall Idea-Fly’s/Hobby People’s liability exceed the original cost of the purchased product.

Some states do not allow the exclusion or limitation of incidental or consequential damages, or allow limitations on

how long an implied warranty lasts, so the above limitations may not apply to you. This warranty gives you specific

legal rights, and you may have other rights which vary from state to state.

LiAbiLiTy AND wARRANTy iNfORMATiON

If you have any questions or need technical support, or if a problem is found that you feel should be under warranty,

please contact the authorized Hobby People/Affiliates service department using the information below. Warranty

repair requires proof of purchase. A copy of your original purchase receipt will be required. Once used, we do offer

repair services as well as replacement parts for those customers who purchased a Mars series quadcopter through

Hobby People, Global Hobby Distributors or one of its affiliate authorized dealers.

To contact the Authorized Hobby People/Affiliates service department

or to purchase replacement parts or option parts:

SERviCE AND SUPPORT

Periodically, updates to the flight controller firmware may be released that provide enhancements and fixes that

improve flight performance and user functions. For information about updating the flight controller firmware using

the Autopilot Configuration program, see the Updating Flight Controller Firmware section on pages 32 and 33.

fLiGhT CONTROLLER fiRMwARE UPDATES

Hobby People/Affiliate Service:

Global Services

18480 Bandilier Circle

Fountain Valley, CA 92708

U.S.A.

Phone: (714) 963-0329

Fax: (714) 964-6236

Email:

[email protected]

Website:

www.hobbypeople.net

Factory Service:

Shenzhen Idea-Fly Technology Co., Ltd.

6th Floor, A3 Building,

China Rich Crown Industrial Park,

Longhua New District, Shenzhen, China.

Phone: 008-755-61267080

Fax: 008-755-61267081

Email:

[email protected]

Website:

www.idea-fly.com

This Operator’s Manual covers both the Standard and FPV versions of the Mars series quadcopter. Depending on

which version you have, some information may not be pertinent. This mostly affects the FPV system in the FPV

version, otherwise, setup, calibration and flying are the same for both versions.

vERSiON iNfORMATiON

REPLACEMENT PARTS

We stock a complete assortment of common replacement parts, such as motors, ESCs, propellers and more for your

Mars series quadcopter. For more information, see the Replacement Parts section on page 36.

hOw-TO viDEOS

An assortment of various How-To videos are provided on the included CD. We strongly recommend watching these

videos to help you visually understand the most important aspects of setting up and flying your new quadcopter.

Crash damage and damage caused by improper use, misuse or other mishandling of your quadcopter is your

sole responsibility and will not be covered under warranty. Propeller damage caused by improper use, misuse or

other mishandling (e.g. rough landings, contacting objects, etc.) is your sole responsibility and will not be covered

under warranty.

Содержание MARS









































Результаты поиска

Содержание MARS

Отзывы:

Похожие инструкции для MARS

Бренды по названию

Популярные бренды

IdeaFly MARS, Руководство оператора

Результаты поиска

Содержание MARS

Отзывы:

Похожие инструкции для MARS

Бренды по названию

Популярные бренды