IdeaFly MARS Скачать руководство пользователя

Страница: 30 / 40

MARS

QUADCOPTER OPERATOR’S MANUAL

2) Using a small Philips head screwdriver, remove the screw from the lower

corner of the FPV monitor, then install the mounting arm bracket onto the

FPV monitor, using the screw you removed.

Do not overtighten the screw or you’ll strip the plastic. We recommend

applying some epoxy or CA to the bracket to hold it more securely

in place.

3) Using a 1.5mm hex wrench, install the mounting arm onto the transmitter

handle, then mount the monitor to the mounting arm, using the knurled

nut to secure it in place.

4) Adjust the mounting arm and the monitor angles to suit, then firmly tighten

the two mounting arm screws and the knurled nut to lock the FPV monitor securely in position.

USiNG ThE fPv SySTEM

MOUNTiNG ThE fPv MONiTOR

1) Carefully thread the mushroom-style antenna onto the antenna mount

and tighten it gently.

USiNG ThE fPv SySTEM

1) Power ON the transmitter and quadcopter, and wait to allow the gyros and flight controller to initialize. Wait another

30 to 45 seconds to allow the camera gimbal to finish initializing.

2) Turn your camera ON, then turn the FPV monitor ON.

3) If no picture (snow) is displayed on the FPV monitor, press and HOLD the

Channel Select/Scan button for 3 seconds, then release it. The FPV monitor

will automatically scan the available channels and lock on the strongest

one. A picture should then be displayed on the FPV monitor.

If you’re using the Idea-Fly WiFi Sports Cam 1080P, you will need to

enable the Analog Video Output by pressing and HOLDING the UP

Arrow button on the right side of the camera for 2 seconds, using a narrow tool, like a hex wrench (see inset photo).

A short audible tone will sound an the display on the back of the camera will go black, indicating the Analog Video

Output is active. If there is still no picture displayed on the FPV monitor, press and HOLD the Channel Select/Scan

button for 3 seconds, then release it again to initiate another channel scan.

Enabling the Analog Video Output may or may not be required for other brands of cameras. For more

information, please refer to the User’s Guide included with your camera.

If you’re flying outdoors, we recommend installing the sunshade onto the FPV monitor to help prevent glare

from interfering with clear viewing of the LCD screen.

CONNECTiNG ThE USb fPv viDEO CAbLE

A micro USB FPV video cable is required to send video from your camera’s

Video Output to the FPV system in the quadcopter. This video cable is

available separately (P/N 163452) if your action camera does not include a

compatible video cable or included with the Idea-Fly WiFi Sports Cam 1080P.

1) Plug the micro USB connector on the video cable into the matching Video

Out port on your camera, then plug the other end of the video cable into

the FPV Video Connector port on the bottom of the quadcopter, making

sure to observe correct polarity.

Before continuing, make sure that you’ve installed the brushless camera gimbal, along with your camera, following

the steps in the Installing the Camera Gimbal section on page 27.

FPV Video Connector*

White

Green

Содержание MARS









































Результаты поиска

Содержание MARS

Отзывы:

Похожие инструкции для MARS

Бренды по названию

Популярные бренды

IdeaFly MARS, Руководство оператора

Результаты поиска

Содержание MARS

Отзывы:

Похожие инструкции для MARS

Бренды по названию

Популярные бренды