background image

ID TECH VP5300M User Manual 

Page | 23  

 

9.

 

Installation 

 

The VP5300M is designed to be mounted on a metal surface and in reasonably close 
proximity to any internal motors and electrical devices that may be operating inside the 
kiosk. However, the unit (like all NFC/RFID devices) is susceptible to RF and electromagnetic 
interference

.  

NOTE: DO NOT mount the VP5300M near (within 3 or 4 feet of) large electric motors, 
computer UPS systems, microwave transmitters, anti-theft devices, radio transmitters, 
routers, or similar electronics. 

 

Close proximity of metal to antenna’s the RF-emitting end can greatly reduce the antenna’s 
range. 

 

Tie all cables neatly with nylon cable-ties and route them so that they are inaccessible and 
invisible to customers. Label the cable ends as "host," "ViVOpay," and "power" to simplify 
connection testing or component replacement, particularly when untrained individuals might 
be involved. 

 

Test the installation using a test card to perform an end-to-end transaction (the same as an 
actual purchase). The NFC antenna front panel's light should illuminate. Even if the 
transaction is declined (as it should be with a test card), it will prove connectivity all the way 
through the system. If possible, the store manager or some other responsible party should 
test each VP5300M on a regular basis (perhaps at the start of each day or at least once per 
week) with a test card to ensure continued operation and functionality. If the unit is 
manually rebooted, it is important to test the contactless reader portion as soon as possible 
afterwards to verify continued communication. Note that the reader automatically reboots 
once every 24 hours on its own, and performs a firmware self-check at that time, to meet 
PCI requirements. 

 

10.

 

Maintenance

 

Clean the VP5300M on a weekly basis with a card reader cleaning card to clean the device’s magnetic 
heads and rollers. Clean the surface of the card insertion bezel with a lint-free cloth.  
 

10.1.

 

Cleaning the VP5300M 

Follow the steps below to clean the VP5300M’s card reader slot. 
 

1.

 

Apply cleaning solution to the middle-third of one side of the cleaning card. 

2.

 

Confirm that the VP5300M is powered on, set the card reader to “cleaning mode,”

1

 and insert 

the cleaning card into the reader’s card slot. 

a.

 

Note:

 If the side of the cleaning card with the cleaning solution faces down, make sure 

to perform the cleaning a second time with the cleaning solution on the card facing 
up. 

 

1

 Use the 

Motor Clean (60-1A) 

command to activate cleaning mode. 

Содержание ViVOpay VP5300M







































Отзывы: