ICP 9MAC/E series Скачать руководство пользователя

Страница: 45 / 48

- 45 -

APPENDIX E

QUICK REFERENCE INFORMATION

PRESSURE SWITCH MAKE/BREAK POINTS

UNIT SIZE

(BTUH)

HIGH PRESSURE SWITCH

MEDIUM PRESSURE SWITCH

LOW PRESSURE SWITCH

Make Point

Break Point

Make Point

Break Point

Make Point

Break Point

60,000

(17.5” casing)

1.21 in.wc max

1.05 in. wc +/-

0.06

0.85 in. wc max

0.70 in. wc +/-

0.05

0.62 in. wc max

0.47 in. wc +/-

0.05

60,000

(21” casing)

1.46 in.wc max

1.29 in. wc +/-

0.07

1.00 in. wc max

0.85 in. wc +/-

0.05

0.64 in. wc max

0.49 in. wc +/-

0.05

80,000

1.58 in.wc max

1.40 in. wc +/-

0.08

1.00 in. wc max

0.85 in. wc +/-

0.05

0.75 in. wc max

0.60 in. wc +/-

0.05

100,000

1.58 in.wc max

1.40 in. wc +/-

0.08

1.08 in. wc max

0.93 in. wc +/-

0.05

0.87 in. wc max

0.72 in. wc +/-

0.05

120,000

1.58 in.wc max

1.40 in. wc +/-

0.08

1.05 in. wc max

0.90 in. wc +/-

0.05

0.80 in. wc max

0.65 in. wc +/-

0.05

Flame Sensor Microamperage:

Microamp Range: 0.5 to 6.0 microamps

Typical Reading: 4 to 6 microamps

Hot Surface Igniter Reading:

The Silicon Nitride igniter in this furnace is not voltage sensitive and will work within the voltage range of 102 to 132 VAC. Hence, there is no

voltage regulation circuits on the furnace control board. A new Silicon Nitride igniter has a normal resistance range of 40 to 70 ohms at room

temperature and is relatively stable over the life of the igniter. The igniter resistance will increase with temperatures above room temperature.

Ohm reading of HSI @ 70°F: 40 to 70 ohms

(resistance will remain relatively stable over the life of the igniter).

Gas Valve Ohm Readings:

PL17-5 to PL17-4: Resistance cannot be measured with an ohm meter because there is a bridge rectifier in the gas valve circuit.

Power Choke (Inductor):

Run unit in cooling mode, measure motor amp draw before power choke. Then re-run unit in cooling mode, but this time measure amp draw without

power choke in line. The amp draw should be higher without power choke. Some ammeters will register a lower amp draw (look for a change in

amperage).

440 08 4001 00

Содержание 9MAC/E series

















































Результаты поиска

Содержание 9MAC/E series

Отзывы:

Похожие инструкции для 9MAC/E series

Бренды по названию

Популярные бренды

ICP 9MAC/E series, Руководство по устранению неисправностей

Результаты поиска

Содержание 9MAC/E series

Отзывы:

Похожие инструкции для 9MAC/E series

Бренды по названию

Популярные бренды