ICP 9MAC/E series Скачать руководство пользователя

Страница: 10 / 48

- 10 -

STEP

ACTION

YES

GO TO

26.

Is 115-vac across the transformer leads?

27.

Replace the transformer.

28.

Is 24-vac across W/W1 and on the modulating furnace control?

You will not be able to check for voltage across W/W1 and C

-24V if the furnace is

connected to a Communicating Wall Control at communication connector PL7. Go to step

29.

You have a defective thermostat, or a break in wiring between thermostat and furnace. Fix

problem.

30.

Disconnect all thermostat leads from the thermostat terminal block and jumper R to W/W1.

Does the furnace respond to the call for heat?

31.

You have an incompatible thermostat. Do any of the following:

- Wire the thermostat C terminal to C

-24V.

- Isolate the W/W1 input with a relay.

- Install ballast resistor across W/W1 and C

-24V.

- Replace the thermostat with a compatible model.

32.

Turn power off. Remove secondary voltage fuse from the modulating furnace control and

check the continuity of the fuse.

33.

Is the secondary voltage fuse open?

34.

Go to page number indicated in Index for the section covering SECONDARY VOLTAGE

FUSE IS OPEN.

INDEX

AMBER LED ON SOLID – Check to make sure the correct model plug PL4 is installed. The
rating plate shows the correct model plug for this furnace.

If the correct model plug is

installed then the control is locked out and will auto reset after 1 hour. Lockout could be due
to any of the following:
-

Flame sense circuit failure.

Gas valve relay stuck open.

Software check error.

Reset power to clear lockout. Replace control if status code repeats.

440 08 4001 00

Содержание 9MAC/E series

















































Результаты поиска

Содержание 9MAC/E series

Отзывы:

Похожие инструкции для 9MAC/E series

Бренды по названию

Популярные бренды

ICP 9MAC/E series, Руководство по устранению неисправностей

Результаты поиска

Содержание 9MAC/E series

Отзывы:

Похожие инструкции для 9MAC/E series

Бренды по названию

Популярные бренды