ICP 9MAC/E series Скачать руководство пользователя | Manualshive

Страница: 16 / 48

background image

- 16 -

Status Code 2

PRESSURE SWITCH DID NOT OPEN - This status code indicates the low, medium, or high pressure switch LPS, MPS, or
HPS is made when a call for heat is initiated. The modulating furnace control will flash status code 2 until the switch opens,
then cycle begins.

STEP

ACTION

YES

NO

GO TO

1.

Turn power off, remove blower door, and disconnect communication connector PL7 (if used)

or the R thermostat lead (if used) from the furnace control board.

2

2.

Turn power on and depress door switch. Use a piece of tape to hold switch closed.

3

3.

Jumper R, W/W1, and W2 thermostat terminals.

4

4.

Does status code 2 flash?

8

5

5.

Does a different status code flash?

6

7

6.

Go to page number indicated in the Index for the section covering the status code.

INDEX

7.

Go to page number indicated in Index for CLEANUP AND START-UP INSTRUCTIONS.

INDEX

8.

Is the inducer motor ON?

18

9

9.

Is 24-vac across ORANGE wire on the low pressure switch LPS and C

OM

-24V on

modulating furnace control?

15

10

10.

Is 24-vac across connector terminal PL1-4 and C

OM

-24V on modulating furnace control?

11

12

11.

The main harness is miswired.

7

12.

Is 24-vac across VIOLET wire on the medium pressure switch MPS and C

OM

-24V on

modulating furnace control?

15

13

13.

Is 24-vac across connector terminal PL1-3 and C

OM

-24V on modulating furnace control?

11

16

14.

Replace modulating furnace control.

7

15.

Replace the pressure switch assembly.

7

16.

Is 24-vac across BROWN wire on the high pressure switch HPS and C

OM

-24V on

modulating furnace control?

15

17

17.

Is 24-vac across connector terminal PL8-4 and C

OM

-24V on modulating furnace control?

11

14

18.

Check the inducer PWM line. To do this disconnect 3-pin connector PL16 from the inducer

motor or the inducer motor adapter harness (when used), and connect a DC voltmeter across

terminals PL16-1 BROWN (+) and PL16-2 YELLOW (-).

Note:

The terminals can be permanently damaged if the voltmeter probe is jammed into the

terminal end of the connector. Use caution when checking.

Run COMPONENT TEST by turning setup switch SW1-6 ON. Does voltage across PL16-1

and PL16-2 change between states as shown below?

- State 1 – OFF (1.0 – 4.0 vdc)

- State 2 – MED (6.0 – 10.0 vdc)

19

14

19.

Replace the inducer motor control (if you have 2 piece design) or the inducer motor

assembly.

7

440 08 4001 00

«
...
14
15
16
17
18
...
»

Содержание 9MAC/E series

















































Отзывы:

Нет отзывов

Похожие инструкции для 9MAC/E series

Бренд: Nagas Страницы: 40

Бренд: Bard Страницы: 41

Бренд: Ducane Страницы: 4

Бренд: Vogelzang International Страницы: 28

Бренд: Cuppone Страницы: 100

Бренд: Fire Chief Страницы: 28

Бренд: Fire Chief Страницы: 30

Бренд: York Страницы: 12

Бренд: York Страницы: 12

Бренд: TCS Страницы: 4

Бренд: Barnstead|Thermolyne Страницы: 36

Бренд: York Страницы: 8

M4RC 92.1% AFUE Upflow

Бренд: Nordyne Страницы: 8

*MQ 97%+ Upfl ow/Horizontal

Бренд: Nordyne Страницы: 12

Бренд: Trane Страницы: 8

Бренд: Trane Страницы: 14

Бренд: Trane Страницы: 16

Бренд: Trane Страницы: 60

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды