ICP 9MAC/E series страница 47 Скачать руководство пользователя

Страница: 47 / 48

- 47 -

Using recorded Modulating rate (MOD%), time of

operation at the Modulating rate (MODT), and

Maximum Heat (MAXT) calculate the Heat Load

(HLR) using:

HLR = (MOD% x MODT) + 65 + (100 x MAXT)

Is HLR<825

Is HLR>1965

MOD% = 40%

Unit will start the next cycle in

Intermediate Heat for 45 seconds

followed by 19 minutes of operation

at 40% rate before switching to

Maximum Heat if the call for heat still

exists.

The Modulating rate

MOD% for this cycle will

be as determined.

Thermostat is satisfied.

Yes

Unit will start the next cycle in

Maximum Heat and will remain

running in Maximum Heat until the

Thermostat is satisfied.

Calculated MOD% will be

calculated to the nearest

1%:

MOD% = (HLR – 65) / 19

MOD% = 100%

Unit will start the next cycle in

Intermediate Heat for 45 seconds

followed by 19 minutes of operation

at the calculated MOD% rate before

switching to Maximum Heat if the

call for heat still exists.

440 08 4001 00

Содержание 9MAC/E series

















































Результаты поиска

Содержание 9MAC/E series

Отзывы:

Похожие инструкции для 9MAC/E series

Бренды по названию

Популярные бренды

ICP 9MAC/E series, Руководство по устранению неисправностей

Результаты поиска

Содержание 9MAC/E series

Отзывы:

Похожие инструкции для 9MAC/E series

Бренды по названию

Популярные бренды