ICP 9MAC/E series Скачать руководство пользователя

Страница: 33 / 48

- 33 -

STEP

ACTION

YES

GO TO

28.

Check the blower motor serial output signal. To do this disconnect PL3 from the furnace

control and connect a DC voltmeter across terminals PL3-4 (+) and PL3-2 (-) on the

modulating furnace control. The voltage should be near 0-vdc but it will fluctuate briefly

several times a second. If you have an analog voltmeter the needle will briefly go high

several times a second. If you have a digital voltmeter with a bar graph it will show a large

change in magnitude on the bar graph several times a second. If you have a plain digital

voltmeter it will show a brief fluctuation in voltage and the magnitude may vary depending

on the volt meter used.

Note:

Some voltmeters will not sense this fluctuation at all. Test your voltmeter on a known

good furnace prior to servicing this product.

Note:

You can also make a simple blinky light with a 1 K



resistor and an LED (RED

works best). These parts can be purchased at a nearby Radio Shack. The schematic is shown

below:

When using the blinky light the LED will flash briefly several times a second when the

blower motor serial output signal is working properly. LED’s are directional and the lead

closest to the flat side goes to PL3-2.

29.

Does the voltage fluctuate as described in step 28?

30.

Reconnect PL3 to the modulating furnace control and connect a DC voltmeter across

terminals PL3-4 BLUE (+) and PL3-2 GREEN (-). Does the voltage fluctuate as described

in step 28?

31.

Disconnect PL13 from the blower motor and connect a DC voltmeter across terminals PL13-

3 BLUE (+) and PL13-4 GREEN (-). Does the voltage fluctuate as described in step 28?

32.

You have an open wire or bad terminal on the BLUE wire between connectors PL3 and

PL13. Repair it or replace harness.

33.

Disconnect PL13 from the blower motor and connect a DC voltmeter across terminals PL13-

3 BLUE (+) and PL13-4 GREEN (-). Does the voltage fluctuate as described in step 28?

34.

You have short to ground on the BLUE wire between connectors PL3 and PL13. Repair it or

replace harness.

35.

The blower motor and furnace control are communicating but the RPM must be below 250.

36.

Disconnect jumper wire across R and W/W1 thermostat terminals.

37.

Remove tape from door switch and turn power off at main disconnect.

38.

Does the blower wheel rub against blower housing?

39.

Does the blower wheel turn freely?

40.

Is blower wheel firmly mounted on motor shaft?

STEP

ACTION

YES

GO TO

41.

Remove tape from door switch and turn power off at main disconnect.

42.

Disconnect both multi-pin connectors from blower control module attached to the blower

motor. Be sure to depress release latches on connectors or they may get damaged.

43.

Remove blower assembly from furnace.

44.

Remove two phillips head or two ¼-in. hex head bolts from blower control module attached

to blower motor.

45.

Carefully lift blower control module off blower motor. Depress latch on internal connector to

disconnect blower control module from motor portion of blower motor. DO NOT PULL ON

WIRES. GRIP PLUG ONLY.

WARNING: Wait at least 5 minutes after disconnecting line voltage from equipment before opening blower motor to

prevent electric shock which can cause personal injury or death.



PL3-4

PL3-2

440 08 4001 00

Содержание 9MAC/E series

















































Результаты поиска

Содержание 9MAC/E series

Отзывы:

Похожие инструкции для 9MAC/E series

Бренды по названию

Популярные бренды

ICP 9MAC/E series, Руководство по устранению неисправностей

Результаты поиска

Содержание 9MAC/E series

Отзывы:

Похожие инструкции для 9MAC/E series

Бренды по названию

Популярные бренды