ICP DAS USA tM Series Скачать руководство пользователя страница 92

Страница: 92 / 144

2.29 ~AA4V

Description:

Reads the power-on DO value or the safe DO value of a
module.

Syntax:

~AA4V[CHKSUM](CR)

~ Delimiter

character

Address of the module to be read (00 to FF)

Command to read the power-on DO value or the
safe DO value

P: Reads the power-on DO value

S: Reads the safe DO value

Response:

Valid command :

!AA(Data)[CHKSUM](CR)

Invalid command:

?AA[CHKSUM](CR)

Delimiter character for a valid command

Delimiter character for an invalid command

Address of the responding module (00 to FF)

(Data)

Power-on DO value or safe DO value.

They are two hexadecimal digits followed by 00.

There will be no response if the command syntax is incorrect,
there is a communication error, or there is no module with the
specified address.

tM Series DIO User Manual, Rev: A1.3 7PH-013-A13

ГК

Атлант

Инжиниринг

–

официальный

представитель

РФ

СНГ

+7(495)109-02-08 [email protected] www.bbrc.ru

Содержание tM Series

















































































































































Результаты поиска

Содержание tM Series

Отзывы:

Бренды по названию

Популярные бренды

ICP DAS USA tM Series, Руководство пользователя

Результаты поиска

Содержание tM Series

Отзывы:

Бренды по названию

Популярные бренды