ICP DAS USA tM Series Скачать руководство пользователя страница 67

Страница: 67 / 144

2.15 $AACN

Description:

Clears the digital input counter of channel N.

Syntax:

$AACN[CHKSUM](CR)

Delimiter

character

Address of the module to be cleared (00 to FF)

Command to clear the digital input counter

The channel to be cleared (0 to F).

Response:

Valid Command:

!AA[CHKSUM](CR)

Invalid Command:

?AA[CHKSUM](CR)

Delimiter character for a valid command

Delimiter character for an invalid command. An
invalid command is returned if the specified
channel is incorrect.

Address of the responding module (00 to FF)

There will be no response if the command syntax is incorrect,
there is a communication error, or there is no module with the
specified address.

tM Series DIO User Manual, Rev: A1.3 7PH-013-A13

ГК

Атлант

Инжиниринг

–

официальный

представитель

РФ

СНГ

+7(495)109-02-08 [email protected] www.bbrc.ru

Содержание tM Series

















































































































































Результаты поиска

Содержание tM Series

Отзывы:

Бренды по названию

Популярные бренды

ICP DAS USA tM Series, Руководство пользователя

Результаты поиска

Содержание tM Series

Отзывы:

Бренды по названию

Популярные бренды