ICP DAS USA tM Series Скачать руководство пользователя страница 90

Страница: 90 / 144

2.28 ~AA3EVV

Description:

Enables/disables the host watchdog and sets the host
watchdog timeout value of a module.

Syntax:

~AA3EVV[CHKSUM](CR)

~ Delimiter

character

Address of the module to be set (00 to FF)

Command to set the host watchdog

1: enable the host watchdog

0: disable the host watchdog

Two hexadecimal digits to represent the timeout
value in tenths of a second, for example, 01 denotes
0.1 seconds and FF denotes 25.5 seconds.

Response:

Valid command:

!AA[CHKSUM](CR)

Invalid command:

?AA[CHKSUM](CR)

Delimiter character for a valid command

Delimiter character for an invalid command

Address of the responding module (00 to FF)

There will be no response if the command syntax is incorrect,
there is a communication error, or there is no module with the
specified address.

tM Series DIO User Manual, Rev: A1.3 7PH-013-A13

ГК

Атлант

Инжиниринг

–

официальный

представитель

РФ

СНГ

+7(495)109-02-08 [email protected] www.bbrc.ru

Содержание tM Series

















































































































































Результаты поиска

Содержание tM Series

Отзывы:

Бренды по названию

Популярные бренды

ICP DAS USA tM Series, Руководство пользователя

Результаты поиска

Содержание tM Series

Отзывы:

Бренды по названию

Популярные бренды