4-1-3
Functions Programmable to Keys
■
P g
bl f
ti k
LOCK KEY “LOCK”
■
Programmable function keys
The following functions can be assigned to the
following programmable function keys.
[EMERGENCY], [Side 1], [Side 2], [Side 3], [I ]*, [II]*,
[III]*, [
W
]*, [
X
]*, [
S
]* ,[
T
]*, [APP]*, [HOME]*, ABC
switch and Toggle switch.
*Simple/10-key models only
LOCK KEY LOCK
Push and hold for 1 sec to electronically lock all
programmable keys except the following:
[PTT], [Moni], [Light], [Lock], [Emergency Single],
[Emergency Repeat], [Surveillance] and [OPT 1/2/3].
Push and hold again for 1 sec, to turn the lock
function OFF.
Consult your Icom dealer or system operator for
details concerning your transceivers programming.
If the key indicator shows the programmed function
key name, push the front panel key ([I],[II] or [III] )
under the key indicator to activate the programmed
function.
LIGHT KEY “LIGT”
Push to turn the transceiver’s backlight ON for about
5 sec. When the backlight function is turned OFF in
user set mode.
SURVEILLANCE KEY “SURV”
Push to turn the surveillance function ON and OFF.
function.
(The function key name in parentheses in the
following explanation is displayed for that key
indicator; e.g. “UF”.
For Non-display model
:
The programmable key functions are limited and
some key functions operate differently on
Simple/10-key models.
When this function is turned ON, the beep is not
emitted and the LCD backlight does not light when a
signal is received or a key is pushed, etc.
HOME KEY “HOME”
Push to return to the stand-by mode.
After editing some information that needs to be
memorized push this key to save the editted
For ABC and Toggle switches:
The programmable key functions to ABC and Toggle
switches are limited.
◇
For All models ( Common operation)
PRIO A AND PRIO B KEYS “PRA” “PRB”
Push to select Priority A or Priority B channel.
memorized, push this key to save the editted
contents in memory before returning to the stand-by
mode.
OPT MOMENTARY KEYS “01M” “02M” “03M”
Push to control the output signal level from the
optional unit connector.
◇
For All models
Push to select Priority A or Priority B channel.
MR-CH 1, MR-CH 2, MR-CH 3 AND MR-CH 4 KEYS
“CH1” “CH2” “CH3” “CH4”
Push to select the memory channels 1,2,3 and 4
directly.
MONI KEY “MON”
➥
Push to mute and release the CTCSS (DTCS)
◇
For All models
(Different operation with Non-display model)
When the following key functions are programmed in
the Non-display model, the key functions may be
limited and some key functions operate differently
from Simple and 10-key models.
HIGH/LOW KEY “H/L”
➥
Push to mute and release the CTCSS (DTCS),
NAC or Talkgroup ID squelch mute. Open any
squelch/deactivate any mute while pushing and
holding this key.
➥
Depending on the pre-set value, pushing and
holding this key for 1 sec to cancel the scan.
This function is valid on transceiver revision 1.3
or later.
Push to select the transmit output power temporarily
or permanently, depending on the pre-set value.
•Ask your dealer for the output power level for each
selection.
•Emits one beep when Low 1 is selected, two beeps
when Low 2 is selected and three beeps when High
is selected. (Non-display model only)
26
▒
NOTE : Assigned functional key selection depends
▒
on programming software setup.
