Icom IC-400PRO Скачать руководство пользователя страница 29

Страница: 29 / 48

OTHER FUNCTIONS

■

DTMF
transmission

Up to 8 DTMF (Dual Tone Multiple Frequency) code channels
are available for storage of often used DTMF codes of up to
24 digits and the automatic DTMF transmission function is
available without using the optional HM-100TN

DTMF MICRO

PHONE

DTMF signaling can be used for remote control via phone
patch system, etc.

[DTMF Autodial]

must be assigned to the desired pro-

grammable key using the optional CS-400PRO

CLONING

SOFTWARE

To transmit a DTMF code:

Push

[DTMF Autodial]

—a DTMF code channel appears.

Push

[

]

[

]

to select the desired DTMF channel.

Push

[DTMF Autodial]

to transmit the DTMF code the

selected DTMF channel.

If the transceiver has a

[Re-dial]

key, the last transmitted

DTMF code is sent immediately when pushing the key.

■

Channel lock
function

This function electronically locks

[

]

[

]

[SCN]

(Scan

Start/Stop)/(ID-MR Select),

[MR-CH 1]

[MR-CH 4]

and

[Hook Scan]

keys (if assigned) to prevent accidental chan-

nel change.

[Ch Lock]

must be assigned to the desired programmable

key using the optional CS-400PRO

CLONING SOFTWARE

➥

Push

[Ch Lock]

for 1 sec. to turn the channel lock func-

tion ON and OFF.

Push

[Ch Lock]

for 1 sec.

KEY ASSIGNMENT

DTMF code channel appears.

KEY ASSIGNMENT

IC-400PRO.qxd 03.6.19 6:13 PM Page 24 (1,1)

Содержание IC-400PRO

















































Результаты поиска

Содержание IC-400PRO

Отзывы:

Похожие инструкции для IC-400PRO

Бренды по названию

Популярные бренды

Icom IC-400PRO, Инструкция по эксплуатации

Результаты поиска

Содержание IC-400PRO

Отзывы:

Похожие инструкции для IC-400PRO

Бренды по названию

Популярные бренды