Icom IC-400PRO Скачать руководство пользователя страница 10

Страница: 10 / 48

BASIC OPERATION

■

Turning power ON

➥

Push [

] to turn the power ON.

■

Channel selection

➥

Push

[

]

[

]

to select the desired operating channel.

• While pushing and holding

[

]

[

]

, the displayed channel

changes continuously until channel number “01” appears.

• When displayed channel stops at channel number “01”, beeps

are emitted.

Private channel selection

Push

[

]

(Bank/Func) to enter the channel bank selection

mode. Then select the desired bank with

[

]

[

]

. Push

[

]

(Bank/Func) again to set the bank.

Push

[

]

[

]

to select the desired operating channel in

sequence.

NOTE:

The selected channel is retained even when the

transceiver is turned off.

Push

[

]

Push

[

]

[

]

Push

[

]

About the password prompt:

If the transceiver is programmed for a start up passcode,
enter the specified 4-digit code.

(The optional CS-400PRO

CLONING SOFTWARE

is required.)

• The keys in the table below can be used for password input:
• The transceiver detects numbers in the same block as identical.

Therefore “01234” and “56789” are the same.

When the “PASSWORD” indication does not clear after
entering 4 digit code, the enter code number is incorrect. In
this case, turn the power off and start over.

KEY

NUMBER

IC-400PRO.qxd 03.6.19 6:13 PM Page 5 (1,1)

Содержание IC-400PRO

















































Результаты поиска

Содержание IC-400PRO

Отзывы:

Похожие инструкции для IC-400PRO

Бренды по названию

Популярные бренды

Icom IC-400PRO, Инструкция по эксплуатации

Результаты поиска

Содержание IC-400PRO

Отзывы:

Похожие инструкции для IC-400PRO

Бренды по названию

Популярные бренды