background image

15

5

GROUP MODE OPERATION

Group mode
(CTCSS)

D

Setting the CTCSS frequency

The IC-400PRO is equipped with 51 CTCSS frequencies for
group mode operation. The group mode operation provides
communication with silent stand-by since you will only receive
calls from group members using the same CTCSS frequency.

First of all, set the same CTCSS frequency for all group mem-
ber’s transceivers.
To access the IC-40Jr or IC-4088S operating in Group mode
(including Smart-Ring function), the same CTCSS frequency
should be set. Select the CTCSS frequency matching the
group code that is set to the IC-40Jr or IC-4088S, referring to
the “Group code/frequency table” in the next page.
For example, when group code “01” is set to the IC-40Jr/IC-
4088S, select “67.0” as CTCSS frequency.

NOTE: 

Only the stations with the same CTCSS frequency

or matching the group code can be heard in group mode
operation.

To turn ON the group mode operation:

q

Push 

[

]

/

[

]

to select the desired channel.

w

While in Function mode, push 

[

O

]

(Bank/Func) for 1 sec.

to enter Set mode.

• Push 

[

O

]

(Bank/Func) for 1 sec. to enter the transceiver into

Function mode.

• The bank and channel can be selected after entering Set mode.

e

Push 

[MONI]

for 1 sec. to enter the individual setting.

r

Push 

[MONI]

several times until “CT” appears.

t

Push 

[

]

/

[

]

to select the desired frequency.

• When “OFF” is displayed, push [DUP] to enables the tone fre-

quency selection, in advance.

y

Push 

[MONI]

for 1 sec. to exit the individual setting, then

push 

[

O

]

for 1 sec. to exit Set mode.

• The under bar indicator appears. (p. 4)

 CT  appears

 [MONI]

Channel*

Bank*

The keys under these indicators can be activated. 

*The bank and channel number 

are continuously displayed af-
ter entering set mode.

Push 

[

O

]

 for 1 sec.

[

IC-400PRO.qxd  03.6.19 6:13 PM  Page 15 (1,1)

Содержание IC-400PRO

















































Отзывы: