Icom IC-400PRO Скачать руководство пользователя страница 8

Страница: 8 / 48

PANEL DESCRIPTION

Key flow chart for the default setting

MICROPHONE CONNECTOR

Connect the supplied microphone or optional DTMF micro-
phone.

NEVER

connect non-specified microphones. The pin

assignments may be different and the transceiver may
be damaged.

MICROPHONE

The supplied microphone has a PTT switch and a hanger
hook.

• The following functions are available when the microphone is on or

off hook:
(The optional CS-400PRO

CLONING SOFTWARE

is required.)

- Automatic scan start when on hook.
- Automatic priority channel selection when off hook.
- Sets to ‘Inaudible’ condition (mute condition) when on hook.
- Sets to ‘Audible’ condition (unmute condition) when off hook.

Normal mode

Function mode

Set mode

: Set the desired level/mode.

: Change the individual setting.

: Change the common setting.

: Push to enter channel bank selection mode.
Push for 1 sec. to enter Normal mode.

: Turn the function ON and OFF.

: [CH Up]

: [ID-MR Select]

: [Bank/Func]

: [CONT/SGL]

: [Call]

: [CH Down]

: [CH Up]

: [Scan Start/Stop]

: [Bank/Func]

: [Dup/Pri]

: [Moni(Audi)]

: [CH Down]

Push [

] for 1 sec.

Push [

] for 1 sec.

Push [

] to turn power ON.

IC-400PRO.qxd 03.6.19 6:13 PM Page 3 (1,1)

Содержание IC-400PRO

















































Результаты поиска

Содержание IC-400PRO

Отзывы:

Похожие инструкции для IC-400PRO

Бренды по названию

Популярные бренды

Icom IC-400PRO, Инструкция по эксплуатации

Результаты поиска

Содержание IC-400PRO

Отзывы:

Похожие инструкции для IC-400PRO

Бренды по названию

Популярные бренды