Icom IC-400PRO Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 48

Icom IC-400PRO Скачать руководство пользователя страница 12

7

3

REPEATER OPERATION

■

Repeater operation

Repeaters allow you to extend the operational range of your
radio.

Normally, a repeater has independent frequencies for receive
and transmit.

■

Accessing a repeater

A repeater amplifies received signals and re-transmits them
on a different channel, allowing you to communicate over
greater distances with improved reliability. When using a
repeater, the transmit channel is shifted from the receive
channel by 30 channels. You can search the accessible
repeater in your local area using the Repeater search scan
function (p. 13).

q

Push

[

]

/

[

]

to select the desired channel from 1 to 8

(repeater output channel).

w

Push

[DUP]

(Dup/Pri) to set duplex.

• “

” appears.

• The duplex setting is only available on channels 1 to 8.

e

While pushing and holding [PTT], speak into the micro-
phone at your normal voice level.

• The displayed channel automatically changes to the transmit

channel (repeater input channel), and “

” appears.

r

Release [PTT] to receive.

t

To cancel the duplex setting, push

[DUP]

(Dup/Pri).

Repeater example;

Receives the channel 31 signal and
the detected audio signals are trans-
mitted on channel 1 simultaneously.

Station A:
Tx: Channel 31
Rx: Channel 1

Station B:
Tx: Channel 31
Rx: Channel 1

Ch 31

Ch 1

Ch 1

Ch 31

IC-400PRO.qxd 03.6.19 6:13 PM Page 7 (1,1)

«
...
10
11
12
13
14
...
»

Содержание IC-400PRO

















































Отзывы:

Нет отзывов