Icom IC-400PRO Скачать руководство пользователя страница 26

Страница: 26 / 48

SELCALL OPERATION

The SelCall mute condition allows silent operation until you
are selcalled.

While in Function mode, push

[DUP]

(CONT/SGL) and

select the single tone to activate the SelCall mute
(‘Inaudible’ condition).

• Push

[

]

(Bank/Func) for 1 sec. to enter the transceiver into

Function mode.

• When the single tone is selected, “SGL” is displayed briefly, and

the under bar appears as below.

Push [

] for 1 sec. to enter Set mode, and push for 1 sec.

again to return to Normal mode.

To monitor the channel;

Push

[MONI]

(Moni(Audi)) for 1 sec. to release the SelCall

mute (audio is emitted; ‘Audible’ condition).

• “

” appears.

To enable SelCall mute;

When “

” appears, push the key to mute the channel

(sets to ‘Inaudible’).

• “

” disappears.

NOTE:

The unmute condition (‘Audible’ condition) may

automatically return to the mute condition (‘Inaudible’ con-
dition) after a specified time period depending on the pre-
setting.

Push

[MONI]

Push

[MONI]

for 1 sec.

Appears

Push

[

]

for 1 sec.

Normal mode

Push

[DUP]

Appears

■

Setting the silent stand-by condition

IC-400PRO.qxd 03.6.19 6:13 PM Page 21 (1,1)

Содержание IC-400PRO

















































Результаты поиска

Содержание IC-400PRO

Отзывы:

Похожие инструкции для IC-400PRO

Бренды по названию

Популярные бренды

Icom IC-400PRO, Инструкция по эксплуатации

Результаты поиска

Содержание IC-400PRO

Отзывы:

Похожие инструкции для IC-400PRO

Бренды по названию

Популярные бренды