manualshive.com logo in svg

ICM Controls ICM1511 Series, Инструкция по персонализированным настройкам и установке

Поделиться
Скачать
ICM Controls ICM1511 Series Скачать руководство пользователя страница 15

(continued from 

previous page)

Thermostat calls 
for heat

5.  Control enters Ignition Carry-Over period (continues to spark for 10 to 30 

seconds.
a.  Turns on indicator light.
b.  If flame is lost and lockout time has not expired, Oil Primary Control 

returns to Trial for Ignition period.

c.  If flame is lost and lockout time has expired, Oil Primary Control enters 

Recycle Mode.

6.  Carry-Over time expires; ignitor turns off.
7.  Enters Run Mode:

a. Flame is monitored until call for heat ends or flame is lost. If flame is lost:

(1)  Control enters Recycle Mode.
(2)  Recycle time starts (60 seconds).
(3)  Burner and valve are turned off.
(4)  Indicator light flashes at 2 seconds on, 2 seconds off.
(5)  Returns to Idle Mode at end of Recycle Mode.

Call for heat is 
satisfied.

1.  ICM1511*, ICM1514* (if burner motor-off delay is disabled):

a. Burner motor and oil valve shut off.
b. Indicator light turns off.

2.  ICM1511*, ICM1512*, ICM1513* (if burner motor-off delay is enabled):

a.  Oil valve shuts off.
b.  Burner motor runs for selected burner motor-off delay time.
c.  Burner motor turns off.
d.  Device returns to Idle Mode.

Reset Button 
pushed two times 
without device 
completing a call 
for heat.

1.  Oil Primary Control enters Restricted Mode.
2.  Indicator light flashes and 1/2 second on, 1/2 second off.
3.  Reset device by pressing and holding reset button for a minimum of 30 

seconds.

Содержание ICM1511 Series

























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды