manualshive.com logo in svg

ICM Controls ICM1511 Series, Инструкция по персонализированным настройкам и установке

Поделиться
Скачать
ICM Controls ICM1511 Series Скачать руководство пользователя страница 13

Check Safety Features

Safe Start
1.  Place a jumper across cad cell terminals.
2.  Follow procedure to turn on burner. Burner must not start, indicator light turns on 

and control remains in Idle Mode.

Simulate Flame Failure:
1.  Follow procedure to turn on burner.
2.  Close hand valve in oil supply line.
3.  Device enters recycle mode.
4.  Device tries to restart system after approximately 60 seconds.
5.  Safety switch locks out approximately in safety switch timing indicated on label. 

Indicator light flashes 1/2 second on, 1/2 second off. Ignition and motor stop and oil 

valve closes.

Simulate Ignition Failure:
1.  Follow starting procedure to turn on burner, but do not open oil supply hand valve.
2.  Observe that safety switch locks out approximately within safety switch timing as 

indicated on the label. Indicator light flashes 1/2 second on, 1/2 second off. Ignition 

and motor stop and oil valve closes.

Содержание ICM1511 Series

























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды