manualshive.com logo in svg

ICM Controls ICM1511 Series, Инструкция по персонализированным настройкам и установке

Поделиться
Скачать
ICM Controls ICM1511 Series Скачать руководство пользователя страница 14

Operation

The ICM Interrupted Ignition Oil Primary Control is a microprocessor-based control. The 

indicator light provides diagnostic information for lockout, recycling and patented cad 

cell status. There is a manual reset button to exit the lockout mode and enter the idle 

mode (See Fig. 1, Page 1). Operation is as follows:

External Action

Oil Primary Control Action:

Power applied to 
control

Internal safety check conducted. If no light or flame is detected and all 
internal conditions are correct, control enters Idle Mode.

Thermostat calls 
for heat

(continued on 

next page)

1.  Shorts across T-T terminals (on a call for heat) in warm air system and/or 

provides power to limit terminals in hydronic system. Networked systems 
may receive a call for heat on network connections 1, 2, 3.

2.  Safety Period (5 seconds) internal and external check for flame or light. If 

flame or light is detected, control remains in the Idle Mode.

3.  When flame or light is not present: 

a.  ICM1514* (if valve-on delay is enabled) will apply power to the burner 

motor and ignitor.

b.  ICM1511*, ICM1512*, ICM1513* (if valve-on delay is enabled) will apply 

power to the burner motor and ignitor, enter/complete valve-on delay 
period and then apply power to the valve.

4.  Control enters Trial for Ignition period.

a.  Monitors burner for flame.
b.  When flame is not detected:

(1) Enters lockout mode (after lockout time of 15, 30, or 45 seconds).
(2) Shuts off valve, ignitor and burner motor.
(3) Flashes indicator light at 1/2 second on, 1/2 second off.
(4) Depress reset button to return to power-up sequence.

c.  When flame is detected, Carry-Over period begins:

Содержание ICM1511 Series

























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды