IBM SAN384B-2, Инструкция по установке, обслуживанию и эксплуатации

Страница: 75 / 190

Follow these steps to install the QSFPs and cables in the 16 Gbps core blades.
These transceivers and cables are used to form the inter-chassis links (ICL) with
neighboring SAN384B-2 and SAN768B-2 backbones. The transceivers should be
installed in the blades before connecting the cables. Because each QSFP contains
four 16 Gbps ports, be aware that any problems with one port could affect all four
ports in the quad if the QSFP has to be replaced.
1. Position one of the QSFP transceivers so that the key is oriented correctly to the
port. Insert the transceiver into the port until it is firmly seated. Transceivers
are keyed so that they can only be inserted with the correct orientation. If a
transceiver does not slide in easily, ensure that it is correctly oriented. When
the transceiver is correctly seated, the status LED will flash amber several times
and then turn solid amber.
2.
Remove the protective cap from the special QSFP cable and insert it into the
transceiver until it is firmly seated. The cables are also keyed to fit into the
transceivers correctly. When the cable is correctly seated, the status LED will
change from amber to green.
3. Repeat steps 1 and 2 for the remaining ICLs.
4. Organize the cables (see “Managing cables” on page 44).
5. Verify the chassis and connector and port status using the switchShow -qsfp
command. A sample of the command output is shown below. The example is
from a SAN384B-2 with a core blade installed in slot 3. Note that the state
reported for an unconnected QSFP (shown QSFP 0 and Ports 0-3 below) is
No_SigDet. This is different from the State of No_Synch that is reported for
regular SFPs that are unconnected. QSFP 7 (ports 3/28-3/31, Index 748-751) in
the following example shows the results for a connected QSFP.
switch:FID128:admin> switchshow -qsfp
switchName: switch_name
switchType: 121.3
switchState: Online
switchMode: Native
switchRole: Subordinate
switchDomain: 75
switchId: fffc4b
switchWwn: 10:00:00:05:1e:4f:eb:00
zoning: ON (zoning_name)
switchBeacon: OFF
FC Router: OFF
Allow XISL Use: OFF
LS Attributes: [FID: 128, Base Switch: No, Default Switch: Yes, Address Mode
0]
Index Slot Port QSFP Address Media Speed
State Proto
=============================================================
256
3 0 0 ------ id 16G No_SigDet FC
257 3 1 0 ------ id 16G No_SigDet FC
258 3 2 0 ------ id 16G No_SigDet FC
259 3 3 0 ------ id 16G No_SigDet FC
260 3 4 1 ------ -- 16G No_Module FC
261 3 5 1 ------ -- 16G No_Module FC
262 3 6 1 ------ -- 16G No_Module FC
263 3 7 1 ------ -- 16G No_Module FC
264 3 8 2 ------ -- 16G No_Module FC
265 3 9 2 ------ -- 16G No_Module FC
266 3 10 2 ------ -- 16G No_Module FC
267 3 11 2 ------ -- 16G No_Module FC
268 3 12 3 ------ -- 16G No_Module FC
269 3 13 3 ------ -- 16G No_Module FC
270 3 14 3 ------ -- 16G No_Module FC
271 3 15 3 ------ -- 16G No_Module FC
736 3 16 4 ------ -- 16G No_Module FC
737 3 17 4 ------ -- 16G No_Module FC
Chapter 3. Starting and configuring the SAN384B-2
43
|