manualshive.com logo in svg

IBM PowerPC 750GX, Руководство пользователя

IBM PowerPC 750GX - мощный процессор для высокопроизводительных систем. Инструкция пользователя доступна для бесплатного скачивания на нашем сайте. Получите полное руководство по эксплуатации на manualshive.com. Узнайте, как максимально эффективно использовать этот продукт для достижения ваших целей.

Поделиться
Скачать
background image

 

User’s Manual

IBM PowerPC 750GX and 750GL RISC Microprocessor

gx_01.fm.(1.2)
March 27,2006 

 

PowerPC 750GX Overview

Page 29 of 377

1.2.1 Instruction Flow

As shown in Figure 1-1, 750GX Microprocessor Block Diagram, on page 25, the 750GX instruction control 
unit provides centralized control of instruction flow to the execution units. The instruction unit contains a 
sequential instruction fetch (Ifetch), 6-entry instruction queue (IQ), dispatch unit, and BPU. It determines the 
address of the next instruction to be fetched based on information from the sequential instruction fetcher and 
from the BPU. See Chapter 6, Instruction Timing, on page 209 for more information.

The sequential instruction fetcher loads instructions from the instruction cache into the instruction queue. The 
BPU extracts branch instructions from the sequential instruction fetcher. Branch instructions that cannot be 
resolved immediately are predicted using either 750GX-specific dynamic branch prediction or the architec-
ture-defined static branch prediction. 

Branch instructions that do not update the LR or CTR are removed from (folded out of) the instruction stream. 
Instruction fetching continues along the predicted path of the branch instruction.

Instructions issued to execution units beyond a predicted branch can be executed but are not retired until the 
branch is resolved. If branch prediction is incorrect, the completion unit flushes all instructions fetched on the 
predicted path, and instruction fetching resumes along the correct path.

1.2.1.1 Instruction Queue and Dispatch Unit

The instruction queue (IQ), shown in Figure 1-1 on page 25, holds as many as six instructions and loads up to 
four instructions from the instruction cache during a single-processor clock cycle. The instruction fetcher 
continuously attempts to load as many instructions as there were vacancies created in the IQ in the previous 
clock cycle. All instructions except branches are dispatched to their respective execution units from the 
bottom two positions in the instruction queue (IQ0 and IQ1) at a maximum rate of two instructions per cycle. 
Reservation stations are provided for the IU1, IU2, FPU, LSU, and SRU for dispatched instructions. The 
dispatch unit checks for source and destination register dependencies, allocates rename buffers, determines 
whether a position is available in the completion queue, and inhibits subsequent instruction dispatching if 
these resources are not available.

Branch instructions can be detected, decoded, and predicted from anywhere in the instruction queue. For a 
more detailed discussion of instruction dispatch, see Section 6.6.1, Branch, Dispatch, and Completion-Unit 
Resource Requirements, on page 237. 

1.2.1.2 Branch Processing Unit (BPU)

The BPU receives branch instructions from the sequential instruction fetcher and performs CR lookahead 
operations on conditional branches to resolve them early, achieving the effect of a zero-cycle branch in many 
cases. 

Unconditional branch instructions and conditional branch instructions in which the condition is known can be 
resolved immediately. For unresolved conditional branch instructions, the branch path is predicted using 
either the architecture-defined static branch prediction or 750GX-specific dynamic branch prediction. 
Dynamic branch prediction is enabled if the BHT bit in Hardware-Implementation-Dependent Register 0 is set 
(HID0[BHT] = 1). 

When a prediction is made, instruction fetching, dispatching, and execution continue along the predicted 
path, but instructions cannot be retired and write results back to architected registers until the prediction is 
determined to be correct (resolved). When a prediction is incorrect, the instructions from the incorrect path 

Содержание PowerPC 750GX


























































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для PowerPC 750GX

Baracoda All in One Printer Communication Protocol Manual preview
All in One Printer
Бренд: Baracoda Страницы: 42
X-Micro XWL-11GPRG Quick Start Manual preview
XWL-11GPRG
Бренд: X-Micro Страницы: 9
X-Micro XWL-11GPAG Quick Installation Manual preview
XWL-11GPAG
Бренд: X-Micro Страницы: 19
SeaLevel 7406e User Manual preview
7406e
Бренд: SeaLevel Страницы: 17
Lindsay Broadband LBON320AC Series Installation And Operation Manual preview
LBON320AC Series
Бренд: Lindsay Broadband Страницы: 4
CNC4PC C52- ESS User Manual preview
C52- ESS
Бренд: CNC4PC Страницы: 11
Cypress Semiconductor CY7C1303BV25 Specification Sheet preview
CY7C1303BV25
Бренд: Cypress Semiconductor Страницы: 19
A.E.B. ARCHIMEDE Fitting Instructions And Warranty Workbook preview
ARCHIMEDE
Бренд: A.E.B. Страницы: 28
Ultra Products Internal All-in-One Digital Media Drive ULT31793 Specifications preview
Internal All-in-One Digital Media Drive ULT31793
Бренд: Ultra Products Страницы: 1
ST METERS AND MORE UM2241 User Manual preview
METERS AND MORE UM2241
Бренд: ST Страницы: 26
Trend Micro R610 Series Quick Start Manual preview
R610 Series
Бренд: Trend Micro Страницы: 2
Roland JV80 Owner'S Manual preview
JV80
Бренд: Roland Страницы: 224
Behringer X-MADI Quick Start Manual preview
X-MADI
Бренд: Behringer Страницы: 15
8e6 Technologies Threat Analysis Reporter TAR HL/SL/MSA Evaluation Manual preview
Threat Analysis Reporter TAR HL/SL/MSA
Бренд: 8e6 Technologies Страницы: 22
Extron electronics IPL Pro Series User Manual preview
IPL Pro Series
Бренд: Extron electronics Страницы: 10
Renesas M38C29T-64LCA User Manual preview
M38C29T-64LCA
Бренд: Renesas Страницы: 6
Lava HQ-ST Plus Brochure preview
HQ-ST Plus
Бренд: Lava Страницы: 2
AMX RDM-2DC Schematic Diagram preview
RDM-2DC
Бренд: AMX Страницы: 1

Бренды по названию

Популярные бренды

Загрузить еще бренды