manualshive.com logo in svg

IBM PowerPC 750GX, Руководство пользователя

IBM PowerPC 750GX - мощный процессор для высокопроизводительных систем. Инструкция пользователя доступна для бесплатного скачивания на нашем сайте. Получите полное руководство по эксплуатации на manualshive.com. Узнайте, как максимально эффективно использовать этот продукт для достижения ваших целей.

Поделиться
Скачать
background image

 

User’s Manual

IBM PowerPC 750GX and 750GL RISC Microprocessor

gx_02.fm.(1.2)
March 27, 2006 

 

Programming Model

Page 91 of 377

For example, if the mtmsr sets the MSR[PR] bit, unless an isync immediately follows the mtmsr instruction, 
a privileged instruction could be executed or privileged access could be performed without causing an excep-
tion even though the MSR[PR] bit indicates user mode.

Instruction-Related Exceptions

There are two kinds of exceptions in the 750GX—those caused directly by the execution of an instruction and 
those caused by an asynchronous event (or interrupts). Either can cause components of the system software 
to be invoked.

Exceptions can be caused directly by the execution of an instruction as follows:

• An attempt to execute an illegal instruction causes the illegal instruction (program exception) handler to 

be invoked. An attempt by a user-level program to execute the supervisor-level instructions listed below 
causes the privileged instruction (program exception) handler to be invoked:

– Data Cache Block Invalidate (dcbi)
– Move-from Machine State Register (mfmsr)
– Move-from Special Purpose Register (mfspr) 
– Move-from Segment Register (mfsr)
– Move-from Segment Register Indirect (mfsrin)
– Move-to Machine State Register (mtmsr)
– Move-to Special Purpose Register (mtspr)
– Move-to Segment Register (mtsr)
– Move-to Segment Register Indirect (mtsrin)
– Return from Exception (rfi)
– TLB Invalidate Entry (tlbie)
– TLB Synchronize (tlbsync)

Note that the privilege level of the mfspr and mtspr instructions depends on the SPR encoding.

• Any mtspr, mfspr, or Move-from Time Base (mftb) instruction with an invalid SPR (or Time Base Regis-

ter [TBR]) field causes an illegal type program exception. Likewise, a program exception is taken if user-
level software tries to access a supervisor-level SPR. An mtspr instruction executing in supervisor mode 
(MSR[PR] = 0) with the SPR field specifying HID1 or PVR (read-only registers) executes as a no-op.

• An attempt to access memory that is not available (page fault) causes the ISI or DSI exception handler to 

be invoked.

• The execution of an sc instruction invokes the system-call exception handler that permits a program to 

request the system to perform a service.

• The execution of a trap instruction invokes the program exception trap handler.

• The execution of an instruction that causes a floating-point exception while exceptions are enabled in the 

MSR invokes the program exception handler.

A detailed description of exception conditions is provided in Chapter 4, Exceptions, on page 151.

2.3.3 Instruction Set Overview

This section provides a brief overview of the PowerPC instructions implemented in the 750GX and highlights 
any special information about how the 750GX implements a particular instruction. Note that the categories 
used in this section correspond to those used in Chapter 4, “Addressing Modes and Instruction Set 

Содержание PowerPC 750GX


























































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для PowerPC 750GX

dbx 902 Manual preview
902
Бренд: dbx Страницы: 8
Panasonic MICROCOMPUTER MN103S Connection Diagrams preview
MICROCOMPUTER MN103S
Бренд: Panasonic Страницы: 5
Panasonic MICROCOMPUTER MN103S Application Note preview
MICROCOMPUTER MN103S
Бренд: Panasonic Страницы: 21
Panasonic FP2 Series Manual preview
FP2 Series
Бренд: Panasonic Страницы: 56
Panasonic FP2 Series Product Manual preview
FP2 Series
Бренд: Panasonic Страницы: 28
Panasonic KX-HTS Series Quick Start Manual preview
KX-HTS Series
Бренд: Panasonic Страницы: 2
Panasonic WJMPU955 - PROCESSING UNIT - TMU Operating Instructions Manual preview
WJMPU955 - PROCESSING UNIT - TMU
Бренд: Panasonic Страницы: 62
Palo Alto Network M-200 Reference Manual preview
M-200
Бренд: Palo Alto Network Страницы: 56
Paradyne 8540 Installation Instructions Manual preview
8540
Бренд: Paradyne Страницы: 12
Ubiquiti NanoBeam M5 Setup preview
NanoBeam M5
Бренд: Ubiquiti Страницы: 3
Alacritech 1000x1 Hardware Installation Manual preview
1000x1
Бренд: Alacritech Страницы: 20
ekwb EK-FB GA AX370 Gaming RGB Monoblock Installation Manual preview
EK-FB GA AX370 Gaming RGB Monoblock
Бренд: ekwb Страницы: 2
8e6 Technologies ER3-100 (5K02-55) Quick Start Manual preview
ER3-100 (5K02-55)
Бренд: 8e6 Technologies Страницы: 74
AXIOMTEK CEM500 Quick Installation Manual preview
CEM500
Бренд: AXIOMTEK Страницы: 2
S&T Kontron SMARC-sXEL User Manual preview
Kontron SMARC-sXEL
Бренд: S&T Страницы: 108
S&T TPMS1209T02-ER User Manual preview
TPMS1209T02-ER
Бренд: S&T Страницы: 28
swiftech MCW5000-64RH Installation Manual preview
MCW5000-64RH
Бренд: swiftech Страницы: 2
Variscite VAR-SOM-MX8M-PLUS Quick Start Manual preview
VAR-SOM-MX8M-PLUS
Бренд: Variscite Страницы: 2

Бренды по названию

Популярные бренды

Загрузить еще бренды