IBM Power 770 Скачать руководство пользователя страница 78 | Manualshive

Страница: 78 / 220

background image

64

IBM Power 770 and 780 (9117-MMD, 9179-MHD) Technical Overview and Introduction

Similarly, the FSP flex cables must be installed in the correct order (see Figure 2-14), as
follows:

1. Install a second node flex cable from node 1 to node 2.
2. Add a third node flex cable from node 1 and node 2 to node 3.
3. Add a fourth node flex cable from node 1 and node 2 to node 4.

Figure 2-14 FSP flex cables

The design of the Power 770 and Power 780 is optimized for use in an IBM 7014-T00 or
7014-T42 rack. Both the front cover and the external processor fabric cables occupy space on
the front left and right sides of an IBM 7014 rack; racks that are not from IBM might not offer
the same room. When a Power 770 or Power 780 is configured with two or more system
enclosures in a 7014-T42 or 7014-B42 rack, the CEC enclosures must be located in EIA 36 or
below to allow space for the flex cables.

«
...
76
77
78
79
80
...
»

Содержание Power 770





























































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Power 770

Бренд: Makita Страницы: 20

MAKSTAR BTW250 Series

Бренд: Makita Страницы: 8

Бренд: E-Lite Страницы: 4

Бренд: TAAG Страницы: 5

Бренд: Wacker Neuson Страницы: 30

Бренд: Himax Страницы: 2

Бренд: Ryobi Страницы: 8

Бренд: Westfalia Страницы: 20

NittaBeltPoly PI-30

Бренд: Nitta Страницы: 16

Бренд: Prince Castle Страницы: 4

Бренд: MAIMAN ELECTRONICS Страницы: 24

Бренд: Radio Shack Страницы: 13

Бренд: Ayce Страницы: 59

Бренд: TDK-Lambda Страницы: 74

Бренд: OfiTE Страницы: 20

Бренд: patura Страницы: 32

Бренд: V-TAC Страницы: 13

Бренд: Kaindl Страницы: 9

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды