IBM Power 770 Скачать руководство пользователя страница 184 | Manualshive

Страница: 184 / 220

background image

170

IBM Power 770 and 780 (9117-MMD, 9179-MHD) Technical Overview and Introduction

Measured commercial workloads show no gain or loss in performance because of mirroring.
High-performance computing (HPC) workload performing huge amounts of string
manipulation might see a slight performance effect.

The Active Memory Mirroring can be disabled or enabled on the management console using
the Advanced tab of the server properties (Figure 4-5).

Figure 4-5 Enabling or disabling active memory sharing

The system must be entirely powered off and then powered on to change from mirroring
mode to non-mirrored mode.

This same frame also gives information about the mirroring status:

򐂰

Desired mirroring mode: The values are either

Off

or

System firmware only

.

򐂰

System firmware mirroring status

– Fully mirrored: The mirroring is completely functional.

– Partially functional: Because of uncorrectable memory failures, some of the hypervisor

elements or objects are not mirrored. The system remains partially mirrored until DIMM
is replaced and the system is rebooted.

– Not mirrored: At the last powering on of the system, the desired state was

mirroring

off

.

򐂰

Mirrorable memory: This is the total amount of physical memory that can be mirrored,
which is based on the DIMMs that are plugged

򐂰

Mirrored memory in use

򐂰

Available mirrored memory

«
...
182
183
184
185
186
...
»

Содержание Power 770





























































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Power 770

Бренд: Nemtek Страницы: 17

Бренд: Nemtek Страницы: 10

Бренд: Nakayama Страницы: 20

Бренд: Parkside Страницы: 78

Бренд: Würth Страницы: 182

Бренд: Wacker Neuson Страницы: 62

Бренд: Milwaukee Страницы: 35

Бренд: Hilti Страницы: 138

Бренд: Parkside Страницы: 103

Бренд: Chicago Pneumatic Страницы: 36

Бренд: joke Страницы: 12

Airetool 2055-R Series

Бренд: Apex Tool Group Страницы: 12

Бренд: OfiTE Страницы: 20

Бренд: Lambda Electronics Страницы: 21

Бренд: HIKOKI Страницы: 48

XPower Powerpack 400 R

Бренд: Xantrex Страницы: 74

Бренд: Keysight Technologies Страницы: 128

Бренд: Stihl Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды