IBM Power 770 Скачать руководство пользователя страница 169

Страница: 169 / 220

Chapter 3. Virtualization

155

See the following sources of information:

򐂰

For information regarding Advance Toolchain, see the following website:

http://www.ibm.com/developerworks/wikis/display/hpccentral/How+to+use+T
ofor+Linux+on+POWER

򐂰

See the University of Illinois Linux on Power Open Source Repository:

http://ppclinux.ncsa.illinois.edu

򐂰

See the following release notes:

– ftp://linuxpatch.ncsa.uiuc.edu/toolchain/at/at05/suse/SLES_11/release_notes.at

05-2.1-0.html

– ftp://linuxpatch.ncsa.uiuc.edu/toolchain/at/at05/redhat/RHEL5/release_notes.at

05-2.1-0.html

VSX support

Yes

Full exploitation requires
Advance Toolchain.

Distro toolchain
mcpu/mtune=p7

Yes

SLES11/GA toolchain has
minimal P7 enablement
necessary to support
kernel build.

Advance
Toolchain support

Yes,
execution
restricted to
Power6
instructions

Yes

Yes,
execution
restricted to
Power6
instructions

Yes

Alternative GNU Toolchain
that explores the
technologies available on
POWER architecture.

64k base page
size

Yes

Better memory utilization,
and smaller footprint.

Tickless idle

Yes

Improved energy utilization
and virtualization of
partially to fully idle
partitions.

Features

Linux releases

Comments

SLES 10 SP4

SLES 11 SP2

RHEL 5.8

RHEL 6.3

Содержание Power 770





























































































































































































































Результаты поиска

Содержание Power 770

Отзывы:

Похожие инструкции для Power 770

Бренды по названию

Популярные бренды

IBM Power 770, Технический обзор и введение

Результаты поиска

Содержание Power 770

Отзывы:

Похожие инструкции для Power 770

Бренды по названию

Популярные бренды