IBM 9006-12C Скачать руководство пользователя страница 31

Страница: 31 / 126

Place the disk drive backplane and cables on the table.

Replacing the disk drive backplane in the 9006-12C

Learn how to replace the disk drive backplane in the IBM Power System LC921 (9006-12C) system.

Procedure

Ensure that you have the electrostatic discharge (ESD) wrist strap on and that the ESD clip is plugged
into a ground jack or connected to an unpainted metal surface. If not, do so now.

Remove the replacement disk drive backplane and cables from the protective plastic envelope.

Move the cables from the old disk drive backplane to the new card.

Replace the disk drive backplane as shown in Figure 14 on page 16.

Insert the disk drive backplane (A) into the system using the alignment slots (B) in the chassis.

Snap the card into place so that it is held by the retaining clips (C).

Replace the two screws (D), one on each side, in the top of the disk drive backplane.

Figure 13. Removing the disk drive backplane and screws

Removing and replacing parts in the 9006-12C

Содержание 9006-12C































































































































Результаты поиска

Содержание 9006-12C

Отзывы:

Бренды по названию

Популярные бренды

IBM 9006-12C, Руководство пользователя

Результаты поиска

Содержание 9006-12C

Отзывы:

Бренды по названию

Популярные бренды